background image

Limited Warranty 

 

Swipe Family Readers Installation Manual 

Page 17 

Exclusions and Limitations  

ROSSLARE shall not be responsible or liable for any damage or loss resulting from 
the operation or performance of any Product or any systems in which a Product is 
incorporated. This warranty shall not extend to any ancillary equipment not furnished 
by ROSSLARE, which is attached to or used in conjunction with a Product, or to any 
Product that is used with any ancillary equipment, which is not furnished by 
ROSSLARE. 
This warranty does not cover expenses incurred in the transportation, freight cost to 
the repair center, removal or reinstallation of the product, whether or not proven 
defective.  
Specifically excluded from this warranty are any failures resulting from Customer's 
improper testing, operation, installation, or damage resulting from use of the Product 
in other than its normal and customary manner, or any maintenance, modification, 
alteration, or adjustment or any type of abuse, neglect, accident, misuse,  improper 
operation, normal wear, defects or damage due to lightning or other electrical 
discharge. This warranty does not cover repair or replacement where normal use has 
exhausted the life of a part or instrument, or any modification or abuse of, or 
tampering with, the Product if Product disassembled or repaired in such a manner as 
to adversely affect performance or prevent adequate inspection and testing to verify 
any warranty claim. 
ROSSLARE does not warrant the installation, maintenance, or service of the Product.  
Service life of the product is dependent upon the care it receives and the conditions 
under which it has to operate.  
In no event shall Rosslare be liable for incidental or consequential damages.  
 

Limited Warranty Terms  

THIS WARRANTY SETS FORTH THE FULL EXTENT OF ROSSLARE ENTERPRISES 

LTD

.

 AND ITS SUBSIDIARIES

 WARRANTY

 

THE TERMS OF THIS WARRANTY MAY NOT BE VARIED BY ANY PERSON

,

 WHETHER 

OR NOT PURPORTING TO REPRESENT OR ACT ON BEHALF OF ROSSLARE

.

 

 

THIS LIMITED WARRANTY IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES

.

 ALL 

OTHER WARRANTIES EXPRESSED OR IMPLIED

,

 INCLUDING WITHOUT LIMITATION

,

 

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 

PURPOSE

,

 ARE SPECIFICALLY EXCLUDED

IN NO EVENT SHALL ROSSLARE BE LIABLE FOR DAMAGES IN EXCESS OF THE 

PURCHASE PRICE OF THE PRODUCT

,

 OR FOR ANY OTHER INCIDENTAL

,

 

CONSEQUENTIAL OR SPECIAL DAMAGES

,

 INCLUDING BUT NOT LIMITED TO LOSS 

OF USE

,

 LOSS OF TIME

,

 COMMERCIAL LOSS

,

 INCONVENIENCE

,

 AND LOSS OF 

PROFITS

,

 ARISING OUT OF THE INSTALLATION

,

 USE

,

 OR INABILITY TO USE SUCH 

PRODUCT

,

 TO THE FULLEST EXTENT THAT ANY SUCH LOSS OR DAMAGE MAY BE 

DISCLAIMED BY LAW

THIS WARRANTY SHALL BECOME NULL AND VOID IN THE EVENT OF A VIOLATION 

OF THE PROVISIONS OF THIS LIMITED WARRANTY

.

 

 

 

Summary of Contents for AY-B1663





















Reviews: