background image

For information on all ROSS products

please visit: www.rosstools.com.au

The ROSS logo and Bull device are trademarks of J.W. Ross Pty Ltd.

WARRANTY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled 

to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or 

damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality 

and the failure does not amount to a major failure.

This product is covered by a 24 month warranty. 

This warranty will not apply:
(i) where this product has been subjected to misuse, abuse, accident or want of care;
(ii) where this product has been used for a purpose for which it was not designed or is not suited;

(iii) where the service of this product has been undertaken by a non-authorised  person or company or if non-

approved parts have been used;
(iv) where this product has been used for industrial purposes.

Should service become necessary during the warranty period, the purchaser should contact an Authorised Ser-

vice Centre or J W Ross. In order to obtain warranty service, the purchaser must present the store receipt show

-

ing the name of the retailer and the date of purchase.

The period of the warranty begins from the original date of purchase, notwithstanding any  

subsequent repair or parts replacement.

Purchaser shall be responsible for all transport charges to and from the Authorised Service 

 

Centre.

Damage in transit is not covered by this warranty. The purchaser should remove from the product any liquids (if 

applicable) before sending the tool for service or repair. The tool should be packed securely to prevent damage.

WARRANTY EXCLUSIONS

Wear parts or service related parts required when performing normal and regular maintenance of this product 

are not covered by warranty unless it is found to be defective by an Authorised Service Centre. These include, 

but are not limited to: Blades 

Distributed in Australia by J W Ross and Sons ( Australia ) Pty Ltd. 
PO Box 352 North Ryde BC, NSW, 1670

For you local service centre: www.jwross.com.au

Ph:1800 251 338

The J.W. Ross policy is one of continuous improvement and the company reserves the right to alter designs, 

colours and specifications without notice.

Summary of Contents for RGB18









Reviews: