manualshive.com logo in svg

Ross NK Routing Systems RCP-QE, User Manual, Page: 29 / 68

Share
Download
Ross NK Routing Systems RCP-QE User Manual Download Page 29

RCP-QE User Guide (v02)

Setting Up the RCP-QE • 4–9

Set

 – click to set the level mask(s).

Salvo Names Tab

Only applicable when the routing system includes an Ultrix router or Ultricore Central Controller.

Salvo

 # (read-only) – the list order number of the salvo.

Name

 (read-only) – the name of the salvo as defined in connected Ultrix router or Ultricore Central Controller.

Enabled

 – enable or disable this salvo within Category Index mode.

Level Names Tab

Only applicable when the routing system includes an Ultrix router or Ultricore Central Controller.

#

 (read only) – the list order number of the level name entry.

Name

 (read-only) – the name of the Level as defined in connected Ultrix router or Ultricore Central Controller.

Enabled

 – enable or disable this salvo within Category Index mode.

Destination / Source Label Access

Enables destinations or sources to be enabled or disabled for button assignment.

#

 (read only) – the list order number of the label entry.

Label

 (read-only) – the name of the Label as defined in connected Ultrix router or Ultricore Central Controller.

Enabled

 – enable or disable this destination or source within Category Index mode.

Lower Toolbar Buttons

Refresh

 – click this button to revert to the configuration previously sent to the RCP-QE. The RCP-QE Connection 

Editor will display the last settings that were sent to the RCP-QE via the Send Configuration button.

Send Configuration

 – click this button to upload the settings to the RCP-QE. All configuration items become 

active only after uploading.

Reboot

 – click this button to reboot the RCP-QE. This function does not clear the RCP-QE settings.

Close

 – click this button to close the RCP-QE Connection Editor in DashBoard.

Changing Device Details

When a control panel is attached to the network, it is interrogated and an editor for the device can be opened in the 
main pane of DashBoard (see 

Figure 4.5

). Information is read from the device and shown in the simulated 

RCP-QE.

To change the details for the RCP-QE:

1.

In the 

Device Details

 frame, click inside the field that you want to change.

2.

Enter the information as required. 

3.

Press 

Enter

.

4.

Send the current configuration file to the device (see “

Sending a Configuration File to a Device

” on 

page 4–33).

You should save the current configuration file regularly (see “

Saving the Current Configuration for the 

RCP-QE

” on page 4–32).

Summary of Contents for NK Routing Systems RCP-QE





































































Reviews:

No comments