Printed In Canada
Having a problem? Call our free, 24-hour technical
support hotline to speak with a live product
specialist located right here in our facility.
Tel: (+1) 613 • 652 • 4886
Email: [email protected]
CAUTION:
Before you set up and operate your switcher, see the
“Important Safety Instructions” in your Setup manual.
FrameGlow Diagnostics
UPGRADE:
Frame is being upgraded. (cycle from yellow to white)
ON
OFF
POWER
UPGRADE
BOOTING:
Frame hardware is booting up. (cycle from blue to white)
ON
OFF
POWER
UPGRADE
BOOTING:
Frame software is booting up.
ON
OFF
POWER
UPGRADE
NORMAL:
Frame is operating normally. There are no warnings. Actual color is user selectable.
ON
OFF
POWER
UPGRADE
WARNING:
Frame is over-temperature or there is a status warning. (flashing red)
ON
OFF
POWER
UPGRADE
CRITICAL:
Frame is critically over-temperature. Auto power-down imminent. (solid red)
ON
OFF
POWER
UPGRADE
PS1
PS2
USB
TALLY
GPIO
REF
IN
OUT
TO FRAME
IN
OUT
SDI 1
PS2
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
PUSH
1
2
3
1
2
3
PUSH
ANALOG IN
ANALOG OUT
AES OUT
AES IN
1
2
3
4
5
6
7
8
1
2
3
4
5
1
1
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1RU Audio Breakout Module (ABM)
Analog In
from Mics
AES In/Out to
Audio Server
Mains
Power
Note:
It is recommended that you always connect the AC Power Adapter to
the device before connecting to Mains Power.
PS1
PS2
SERIAL
TALLY
GPIO
LTC
REF
OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
IN
MV OUT
OUT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
IN
SD
AES1
AES2
1 2 3 4 5 6 7 8
UPGD
Analog
Outputs
SDI-Audio Loop
(
IN24 to OUT
)
(
OUT14 to IN
)
ABM 1 —
IN24 to OUT
/
OUT14 to IN
ABM 2 —
IN23 to OUT
/
OUT13 to IN
ABM 3 —
IN22 to OUT
/
OUT12 to IN
Important:
Ensure that Phantom Power is turned off for the Analog Input unless you are connecting a micro-
phone that requires phantom power. Connecting the line out from an audio device to the analog input with phan-
tom power on could damage the audio device and/or the 1RU Audio Breakout Module. For added safety, a TRS
phone connecter should be used for line in audio sources.
Note:
Support for the 1RU Audio Breakout Module (ABM) is not available in UHDTV1 at this time.
Analog Audio Input Specifications
Input Impedance
Maximum Level
Frequency Response
Signal to Noise Ratio
“A” weighting
CCITT weighting
THD
Amplitude Linearity
Crosstalk
XLR: 2K ohm
¼” Jack: 10K ohm
+24dBu
±0.3dB (22Hz to
20kHz @ Fs = 48kHz)
-95dB
-98dB
-107dB
>93dB or <0.002%
<0.8dB @ -100dBFS
-94dB
Analog Audio Output Specifications
Maximum Level
Frequency Response
Signal to Noise Ratio
THD
Amplitude Linearity
Crosstalk
+24dBu
±0.4dB (22Hz to
20kHz @ Fs = 48kHz)
-103dB
>93dB
<0.3dB @ -100dBFS
-106dB (20Hz to
20kHz)
Power Consumption
Audio Breakout
Module
45W 3.75A 12V
