background image

POSITION YOUR ROUTER 

The gateway lets you get access of your 2.4Ghz WiFi and ZigBee network from virtually anywhere within the 
operating range of your wireless network. However, the operating distance of range of your wireless 
connection can vary significantly depending on the physical placement of your router. For example, the 
thickness and number of walls the wireless signal passes through can limit the range. For best results, place 
your gateway: 

Near the centre of the area where your computers or sensor devices operate, and preferably within the line 
of sight to your wireless devices. 

Keeping the number of walls and ceilings between the gateway and your devices to a minimum. 

Away from electrical devices that are potential sources of interference. Equipment that might cause 
interference includes ceiling fans, microwaves, computers, the base of a cordless phone, or a 2.4Ghz 
cordless phone. 

Away from any large metal surfaces, such as a solid metal door or aluminium studs. Large expanses of 
other materials such as glass, insulated walls, fish tanks, mirrors, brick, and concrete can also affect your 
wireless signal. 

Summary of Contents for RSG-3000

















Reviews: