ROSIERES RIFS4BV, User Manual

Page: 9 / 32

EN
9
This deactivation will not be applied
to all the functions, as for example the
beep for on/off, the ending of the timer
or the locking/unlocking of the touch
keys always remain activated.
To once again activate all the beeps
that accompany each action, again
simultaneously press the touch key
(11) and the locking touch key (6)
for three seconds. The time indicator
(12) will display “On”
Pause Function
This function puts the cooking process
on pause. The timer will also be
paused if it is activated.
Activating the Pause function.
Touch the Pause sensor (8) for one
second. The pilot (9) lights up and
the power indicators will show the
symbol to indicate cooking has
been paused.
Deactivating the Pause function
Touch Pause sensor (8) again.
The pilot (9) turns off and cooking
resumes under the same power and
timer settings that were established
before the pause.
Booster Function
This function supplies “extra” power
to the plate, above the nominal value.
Said power depends on the size of the
plate, with the possibility of reaching
the maximum value permitted by the
generator.
1 Slide the finger above the
corresponding cursor slider (2)
until the power indicator (3) shows
“9” and keep the finger pressed for
one second, or touch directly on “B”
and keep pressed the finger for one
second.
2 The power level indicator (3) will
show the symbol , and the plate
will start to supply extra power.
The Booster function has a maximum
duration specified in Table 1. After this
time, the power level will automatically
adjust to 9. A beep sounds.
On activating the Booster function in
one hotplate, it is possible that the
performance of some of the others
may be affected, reducing its power to
a lower level, in which case this will be
displayed on its indicator (3).
Deactivation of Booster Function,
before its working time passes, can
be done either by means of touching
cursor “slider” modifying its power level
or repeating step 3.
Timer Function
(countdown clock)
This function facilitates cooking given
that you don’t have to be present: You
can set a timer for a plate, and it will
turn off once the desired time is up.
For these models, you can
simultaneously program each plate
for durations ranging from 1 to 90
minutes.
Setting a timer on a plate.
Once the power level is set on the
desired zone, and while the decimal
dot of the zone keeps on, the zone
will be able to be timed.
To that end:
1 Touch sensor (10) or (11).
Timer Indicator (12) will show “00”
and corresponding zone indicator
(3) will show t
he symbol blinking
alternately with its current power
level.
2 Immediately afterwards set a
cooking time between 1 and 99
minutes, using the sensors (10)
& (11). With the first one the
value will start at 60, whereas with
the second it will start at 01. By
keeping sensors (10) & (11)
pressed, the value will be restored
to 00. When there is less than one
minute left, the clock will begin to
count down in seconds.
3 . When the timer indicator (12) stops
flashing, it will start to count down
the time automatically. The indicator
(3) relating to the timed hotplate
will alternately display the selected
power level and the symbol ,.
Once the selected cooking time has
elapsed, the heating zone being timed
is turned off and the clock emits a
series of beeps for several seconds.
To turn off the audible signal, touch
any sensor.The timer indicator (12)
will display a flashing 00 beside of
the decimal dot (4) of the selected
zone. If the heating zone turned off is
hot, its power indicator (3) will display
alternately the H symbol and a “-“.
If you wish to time another hotplate
at the same time, repeat steps 1 to 3.
If one or more zones are already
timed, the timer indicator (12) will
show by default the shortest remaining
time to finish, showing a “t” on the
related zone. Rest of timed zones will
show on their corresponding indicator
zones the decimal dot blinking. When
cursor ”slider” of another timed zone
is pressed, the timer will show the
remaining time of that zone for a few
seconds and its indicator will show
its power level and the “t” alternately.
Changing the programmed time.
For modifying programmed time,
cursor “slider” (2) of timed zone has
to be pressed. Then it will be possible
to read and modify the time.
Through sensors (10) and (11),
you can modify the programmed time.
Disconnecting the clock
If you wish to stop the clock before the
programmed time is up, this can be
done at any time by simply adjusting
its value to ‘--’.
1 Select the desired plate.
2 Adjust the value of the clock to “00”
by using the sensor (10). The
clock is cancelled. This can also be
done more quickly by pushing the
“sensors (10) and (11) at the
same time.
Power Management function
All models are equiped with a power
limiting function (Power Management).