Rosemount 8732 Series Reference Manual Download Page 149

Page: 149 / 190

Reference Manual

00809-0100-4663, Rev BA
January 2010

E-9

Rosemount 8732

FISCHER AND PORTER
SENSORS

Connect coil drive and electrode cables as shown in Figure E-6.

Model 10D1418 Sensor
to Rosemount 8732
Transmitter

Figure E-6. Wiring Diagram for
Fischer and Porter Sensor
Model 10D1418 and
Rosemount 8732

Table E-7. Fischer and Porter
Model 10D1418 Sensor Wiring
Connections

ROSEMOUNT 8732 TRANSMITTER

Electrode Connections

Coil Connections

Rosemount 8732

Fischer and Porter Model 10D1418 Sensors

Chassis Ground

This is a pulsed DC magnetic flowmeter.

Do not connect AC power

to the sensor

or to terminals 1 and 2 of the
transmitter

, or replacement of the

electronics board will be necessary.

Summary of Contents for 8732 Series































































































































































































Search results

Summary of Contents for 8732 Series

Reviews:

Brands by name

Popular brands

Rosemount 8732 Series, Reference Manual

Search results

Summary of Contents for 8732 Series

Reviews:

Brands by name

Popular brands