manualshive.com logo in svg

Rosemount 702, Reference Manual

Share
Download
Rosemount 702 Reference Manual Download Page 14

Reference Manual

00809-0200-4702, Rev BA

June 2010

Rosemount 702

2-2

Switch Connections

The 702 is compatible with a number of simple switches. When ordered in the 
optional configuration for Liquid Hydrocarbon Detection, option code 61, the 
702 is compatible with Tyco

®

 TraceTek

®

 Fast Fuel Sensors and TraceTek 

sensing cable. Figure 2-1 on page 2-3 shows the correct input connections to 
the switch terminals on the transmitter. To ensure a proper switch connection, 
anchor the switch lead wires into the appropriate compression terminals and 
tighten the screws.

Switch Leads

If the switch is installed in a high-voltage environment and a fault condition or 
installation error occurs, the sensor leads and transmitter terminals could 
carry lethal voltage. Use extreme caution when making contact with the leads 
and terminals.

Use the following steps to wire the sensor and power supply to the 
transmitter:

1.

Remove the transmitter enclosure cover (if applicable).

2.

Attach the sensor leads according to the wiring diagram Figure 3-3 on 
page 3-4.

3.

Connect the power module.

4.

Verify the connection by viewing the LCD.

5.

Replace the cover and tighten (if applicable).

DEVICE SENSOR 
CONFIGURATION

Remove the power module-side housing cover to expose the terminal block 
and HART communication terminals, then connect the power module to 
power the unit for configuration.

The Rosemount 702 will receive any HART communication from a handheld 
Field Communicator, or AMS Wireless Configurator. When using a Field 
Communicator, any configuration changes must be sent to the transmitter 
using the 

Send

 key (F2). AMS Wireless Configurator configuration changes 

are implemented when the 

Apply

 button is clicked.

AMS Wireless Configurator

AMS Wireless Configurator is capable of connecting to devices directly, using 
a HART modem, or with the Gateway. When configuring on the bench with a 
HART modem, double click the device icon, then choose the Configure/Setup 
tab (or right click and select Configure/Setup). Configure the device settings 
using the Direct Connection menu. When configuring with the Gateway, 
double click the device icon then choose the Configure/Setup tab (or right 
click and select Configure/Setup). Configure the device settings using the 
Wireless Connection menu.

To check or change sensor configuration using a Field Communicator, enter 
the following Fast Key Sequence: 2, 2, 2.

Summary of Contents for 702





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands