Rosemount 3107 Reference Manual Download Page 26 | Manualshive

Page: 26 / 148

background image

Reference Manual

00809-0200-4841, Rev BA

Section 3: Installation

December 2014

Section 3: Installation

16

3.4

Electrical installation

3.4.1

Connecting the transmitter

The Rosemount 3490 Series is a two-wire loop-powered transmitter accepting power supplies
as follows:



12 to 40 Vdc in a non-hazardous area (ordinary location)



12 to 30 Vdc in a hazardous area (classified location)

Note



To comply with the CSA requirements, the transmitters must be powered from a
Rosemount 3490 Series Control Unit or class 2 or separate extra-low voltage (SELV)
source.



Other devices may reset if connecting the transmitter to a multi-drop system while the
loop is powered. De-energize the loop to avoid devices being reset.

Each transmitter is supplied with a factory-fitted PVC sheathed, two-core, shielded cable for
communications and external power supply connections. There are no cable conduit entries
and no covers to remove. The cable may be cut to length on site or may be extended using a
junction box and suitable extension cable.

See

“Wiring to allow HART communication” on page 18

if HART digital communication is

required.

Installation in a non-hazardous area (ordinary location)

The 3107 and the 3108 are suitable for non-hazardous (ordinary location) applications.

To connect the transmitter:

1.

Make sure that the power supply is disconnected.

2.

Connect the cable wires as shown in

Figure 3-8 on page 17

, taking note of the required

voltage of

12 to 40 Vdc for non-hazardous (ordinary location) applications

.

Installation in a hazardous area (classified location)

The 3107 and the 3108 are suitable for Intrinsically Safe (IS) applications.

Appendix B: Product

has the safety approval information and control drawings.

When the transmitters are used with a Rosemount 3490 Series Control Unit, no additional
safety barriers are required as the control unit output is Intrinsically Safe.

If powering the transmitter from any other source, ensure a suitable Intrinsically Safe (IS) barrier
is fitted in the non-hazardous area. The barrier must be chosen such that its output parameters
Uo, Io and Po are less than Ui, Ii and Pi of the transmitter (see

Appendix B: Product Certifications

for the parameter values). In addition, the sum of the capacitance and the inductance of the
transmitter and any extra cable fitted must not exceed the maximum specified for the barrier.
Suitable barriers include the MTL products 706, 706S, 787, and 787S.

«
...
24
25
26
27
28
...
»

Summary of Contents for 3107





















































































































































Reviews:

No comments

Related manuals for 3107

Brand: XIEGU Pages: 48

Brand: XIEGU Pages: 13

Brand: Eaton Pages: 2

Brand: R.V.R. Elettronica Pages: 12

si792 D-FF Series

Brand: Hach Pages: 2

Brand: Vaisala Pages: 154

Brand: Fairchild Pages: 8

Brand: Ramsey Electronics Pages: 24

Brand: Team Electronic Pages: 27

Audio-Transceiver-CAT

Brand: G&D Pages: 44

PYROTEC PFS Pocket

Brand: GALAXIS SHOWTECHNIK Pages: 17

Brand: Datcon Pages: 24

THERMOPOINT TM/J-500

Brand: NIVELCO Pages: 28

Brand: YEONHWA M TECH Pages: 19

WEKA 29710 Series

Brand: ARCA Pages: 32

W-DMX Micro T-1 TRX G5

Brand: Chauvet Professional Pages: 15

Rosemount 2051G

Brand: Emerson Pages: 90

Brand: Emerson Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands