manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 84

76

Reference Manual

00809-0100-4803, Rev GA

Installation

September 2017

Installation

Note

Do not connect the power across the test terminals. Power could damage the test diode in the test 
connection.

3. If the optional process temperature input is not installed, plug and seal the unused conduit 

connection. If the optional process temperature input is being utilized, see 

“Install optional process 

temperature input (Pt 100 RTD sensor)” on page 76

 for more information.

When the enclosed pipe plug is utilized in the conduit opening, it must be installed with a minimum 
engagement of five threads in order to comply with flameproof/explosion-proof requirements. 

4. If applicable, install wiring with a drip loop. Arrange the drip loop so the bottom is lower than the 

conduit connections and the transmitter housing.

5. Reinstall the housing cover and tighten so that metal contacts metal to meet 

flameproof/explosion-proof requirements.

Figure 3-9

 shows the wiring connections necessary to power a Rosemount 3051SMV and enable 

communications with a Hand-held Field Communicator.

Figure 3-9. Transmitter Wiring

A. Power supply

Note

Installation of the transient protection terminal block does not provide transient protection unless the 
Rosemount 3051SMV housing is properly grounded. See 

“Grounding” on page 79

 for more information.

Install optional process temperature input (Pt 100 RTD sensor)

Note

To meet ATEX/IECEx Flameproof certification, only ATEX/IECEx Flameproof cables (temperature input 
code C30, C32, C33, C34 or customer supplied equivalent) may be used.

1. Mount the Pt 100 RTD Sensor in the appropriate location. 

Note

Use shielded four-wire cable for the process temperature connection.

Without optional process temperature 

connection

 With optional process temperature 

connection

A

RL ≥ 250Ω

A

RL ≥ 250Ω

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands