manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 26

18

Reference Manual

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

Sending a saved configuration

1. To send a saved configuration, open 

Engineering Assistant

 in offline mode and select 

File>Open

. 

2. Navigate to the saved .smv file to be sent. Select 

Open

.

3. The 

Engineering Assistant Device Connection

 screen will appear, see 

Figure 2-12 on page 17

. 

4. Select the 

Search

 button located in the lower right corner of the screen. Engineering Assistant will 

begin to search for connected devices.

5. When the search is completed, select the device to communicate with and select 

Send

 

Configuration

 button.

6. Once the configuration is finished being sent to the device, a notification appears.

7. If finished with the configuration process, close Engineering Assistant.

2.4.9

Other fluid configurations

Natural gas AGA No. 8 detail characterization or ISO 12213, molar 
composition flow configuration

1. Expand the 

Gas

 category. 

2. Expand the 

Natural Gas

 category.

3. Select 

AGA Report No. 8 Detail Characterization Method

 or 

ISO 12213, Molar Composition 

Method

.

4. Select 

Next >

 to proceed to the 

Fluid Composition 

tab. 

Figure 2-13

 shows an example of the 

Fluid 

Composition

 tab for AGA Report No. 8 Detail Characterization Method. The ISO 12213, Molar 

Composition Method

 Fluid Composition

 tab will require the same information.

Figure 2-13. Fluid Composition Tab

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands