Rosemount 3051S Series Reference Manual Download Page 155 | Manualshive

Page: 155 / 190

background image

Specifications and Reference Data

147

Specifications and Reference Data

September 2017

Reference Manual

00809-0100-4803, Rev GA

A.4 Accessories

A.4.1 Rosemount Engineering Assistant (EA) software packages

The Rosemount Engineering Assistant software supports flow configuration for the Rosemount 3051SMV. The package is
available with or without modem and connecting cables. All configurations are packaged separately.

For best performance of the EA Software, the following computer hardware and software is recommended:



Pentium-grade Processor: 500 MHz or faster



Operating system: Windows

™

Professional 7, 8.1, or 10.

–

32-bit

–

64-bit



256 MB RAM



100 MB of available hard disk space



RS232 serial port or USB port (for use with HART modem)



CD-ROM

Engineering Assistant software packages

Accessories

Code

Product description

EA

Engineering Assistant software program

Software media

3

EA Rev. 6 (compatible with Rosemount 3051SMV only)

Language

E

English

Modem and connecting cables

O

None

H

Serial Port HART modem and cables

B

USB Port HART modem and cables

License

N1

Single PC license

N2

Site license

Typical model number:

EA

3 E O

N1

Item description

Part number

Serial Port HART modem and cables only

03095-5105-0001

USB Port HART modem and cables only

(1)

1. Supported

by

SNAP-ON

™

EA with AMS Device Manager version 6.2 or higher.

03095-5105-0002

«
...
153
154
155
156
157
...
»

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Related manuals for 3051S Series

SXNP10 - DIGITAL PIANO

Brand: Panasonic Pages: 63

Brand: NanoEnTek Pages: 4

Brand: Ralston Instruments Pages: 52

Pasport PS-2138

Brand: Pasco Scientific Pages: 26

Brand: Hanna Instruments Pages: 2

Brand: Percussion Play Pages: 3

Brand: JUMO Pages: 150

Brand: Jaquet Pages: 27

Brand: Omicron Pages: 76

Brand: Galileo Pages: 30

Brand: Bitzer Pages: 8

Brand: LaserLiner Pages: 64

Brand: Kabelmat Pages: 27

Brand: Rubicson Pages: 4

Brand: LaMotte Pages: 2

SeeSnake microReel

Brand: RIDGID Pages: 414

Brand: Simpson Pages: 19

Fuel Metering Valves eXVG

Brand: Hamilton Sundstrand Company Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands