manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 105

97

Reference Manual 

00809-0100-4803, Rev GA

Operation and Maintenance

September 2017

Operation and Maintenance

4.4.1

Flow/energy calculation verification (test calculation)

(Fully compensated mass and energy flow feature board only):

The Flow and Energy Calculation Verification Test allows the user to verify the flow configuration of the 
Rosemount 3051SMV by entering expected values for the differential pressure, static pressure, and 
process temperature variables. Under the 

Flow/Energy Calculation Verification

 heading, perform the 

following steps: 

1. Select the 

Enable Test Calculation

 button.

2. Select 

Simulate DP

 option. Select 

Next

.

3. Select 

DP Units

 from the drop-down menu. Select 

Next

.

4. Enter the DP Value corresponding to the desired flow rate simulation. Select 

Next

.

5. Repeat steps 

1

–

3

 for static pressure (Simulate AP/GP) and process temperature (Simulate PT), if 

applicable.

6. Select 

View Results

. Select 

Next

. The simulated flow rate and corresponding flow properties will be 

shown. Select 

Next

.

7. Select 

Exit

. Select 

Next

. Leaving the 

Enable Test Calculation

 window automatically returns all process 

variables fixed by the test calculation method to live process variable measurements.

4.4.2

Configuring fixed process variables

Under the 

Fixed Process Variables

 heading, the user may temporarily set the differential pressure, static 

pressure or process temperature to a user defined fixed value for testing purposes. Once the user leaves 
the 

Configure Fixed Variable

 method, the fixed process variable will be automatically returned to a live 

process variable measurement. 

4.4.3

Analog output loop test

Under the 

Analog Output Verify 

heading, a Loop Test can be performed by selecting the 

Loop Test

 button. 

The loop test command verifies the output of the transmitter, the integrity of the loop, and the 
operations of any recorders or similar devices installed in the loop.

Mass and energy flow Fast Keys

1, 2, 3

Mass and energy flow Fast Keys

1, 2, 4

Direct process variable output Fast Keys

1, 2, 3

Mass and energy flow Fast Keys

1, 2, 2

Direct process variable output Fast Keys

1, 2, 2

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands