manualshive.com logo in svg

Rose electronics Intuvia, Owner'S Manual

Share
Download
Rose electronics Intuvia Owner'S Manual Download Page 24

24

5.2.7  Switching the walk assist function on/off

The walk assistance may help you push your e-bike. The assistance provided depends on the selected gear and may 
reach up to 6 km/h. The lower the selected gear, the lower the speed in the push assistance mode (at full power).

Only use the walk assist function while pushing the e-bike. There is a risk of injury, if the wheels of the e-bike are not in 
contact with the ground while using the walk assistance.

Briefly push the 

WALK

 button (1) on the control unit to activate the 

walk assistance. Push the “

+

” button (2) within 3 secs after activation 

and hold it down.

 

→

The e-bike drive is activated.

Note: You cannot activate the walk assist function in the assistance 

level OFF.

The walk assistance will switch off, if:

•  you release the “

+

” button (2),

•  the wheels of the e-bike are locked (e.g. through braking or 

knocking against an obstacle),

•  the speed exceeds 6 km/h.

5.2.8  Checking the battery charge

Check the battery capacity before your ride (see “Battery charge indicator“ on page 26).

5.2.9  Display settings

DANGER

Risk of accident due to using on-board computer while riding!

Reading from the computer display or changing settings while riding may distract from the traffic situation. This may 
result in accidents caused by delayed or hindered rider responses!

•  For all settings other than those concerning the level of assistance, you should stop off the road to enter the 

respective data.

Press the 

i

 button on the on-board computer to switch between 

the different indication functions. You can choose between the 
following functions:

•  Time: current time

•  Maximum: maximum speed achieved since the last reset

•  Average: average speed achieved since the last reset

•  Trip time: trip time since the last reset

•  Range: estimated range of the available battery charge (for 

constant conditions such as assistance level, route profile etc.)

•  Odometer: display of the total distance travelled (cannot be 

reset)

To reset all resettable values, press the 

RESET

 button until the indication is set to zero. Please read the manufacturer’s 

manual for more information on changing the basic settings.

1

2

TURBO

SPORTTOUR

ECO

OFF

MPH

KM/H

Rei

chw

eite

AMM

PMWH

MIN

MPH

KM

/H

 

RESET

TURB

O

SPOR

T

S

TOUR

ECO

OFF

MPH

KM/

H

Reichweite

A MM

PMW

H

MIN

MPH

KM

/H

i

i

Summary of Contents for Intuvia





































Reviews:

No comments

Brands by name

Popular brands

Load more brands