RONVIG DENTAL Calaject Instructions For Use Manual Download Page 3

3

   TEST AND TRAINING  

New users must read these instructions carefully and familiarize themselves with the functions 
and different programs before using CALAJECT™. 

CLEANING

• The CALAJECT™ unit, han cord, Handpiece Holder should be disinfected with an

EPA-registered disinfectant unless the item is visibly contaminated with blood; in that case

a tuberculocidal agent (or a disinfectant with specific label claims for HBV and HIV) or a

1:100 dilution of a hypochlorite solution (500–600 ppm free chlorine) should be used.

• The foot cord can be wiped over with a clean cloth moistened with a mild detergent

or disinfection solution.

Do not immerse into liquid. Do not autoclave. The CALAJECT™ unit and the 
handpiece contain sensitive electronic components that do not withstand   
sterilization or immersion in liquid. 

• Clean the cartridge barrel in water and a mild detergent.

 STERILIZATION 

The cartridge barrels are delivered non-sterile and should be sterilized before first use.

Place the cartridge barrel in a sterilization pouch and seal it. Sterilize it in a steam 
sterilization autoclave at 121°C / 250°F for 15 minutes, or at 134°C / 275°F for 3 minutes.  
The cartridge barrel may get a frosted appearance after a number of sterilizations, so it is 
recom-mended to replace the cartridge regularly in order to keep a clear view to the cartridge. 
The cartridge barrel should also be replaced if it is damaged or if the thread appears to be worn.
Replacement barrels (3 pcs. per pack) can be ordered through your CALAJECT™ dealer. 

   PLACING

CALAJECT™

 

should be placed on a stable base during use. Ensure good access to all sockets 

and plugs during use and charging. 

CHARGING

CALAJECT™ may only be charged with the charger supplied with the system. Use   

of other chargers may damage the equipment and compromise the electrical safety.  

For battery lifetime reasons it is recommended to remove the mains cable during use and oper-

ate on battery only. Avoid draining the battery completely - that might shorten longevity as well.

RD_brugervejledning_IFU-CALAJECT-USA-2019.01-VER 7_090119.indd   3

16-01-2019   17:41:06

Summary of Contents for Calaject













Reviews: