Ronda 5010.B Technical Instructions Download Page 10

Page: 10 / 25

Technical Instructions 5130.D

10/2013 N

RONDA AG, Lausen, Switzerland, Phone ++41 (0)61 926 50 00, www.ronda.ch, [email protected]

2000.574.G

Main plate

3305.282.CO

Cannon pinion with driver (Aig.2)

3301.243

Hour wheel (counter 12h)

(Alarm)

3301.244

Hour wheel (counter 24h)

(Chrono)

2030.017.CO

Centre bridge

Centre bridge held by 1 screw 4000.250.

4000.250

Screw

3001.055.FI

Sliding pinion

3000.177.CO

Setting stem

3017.049

Setting lever

3905.049

Setting lever jumper (3 positions)

10.

Setting lever jumper held by 1 screw 4000.250.

4000.250

Screw

11.

3015.081

Yoke (3 positions)

12.

3905.067

Yoke spring

13.

Tensioning the spring arm.

3406.030

Pusher jumper B

14.

Put the grey jumper between the two posts on the further side.

3406.038

Pusher jumper A

15.

Put the yellow jumper between the two posts on the closer side.

3622.040

Stator

16.

Mark |Z| on stator.

3622.039

Stator (counter 6h, 9h, chrono)

17.

3622.039

Stator (counter 6h, 9h, chrono)

18.

3622.039

Stator (counter 6h, 9h, chrono)

19.

Summary of Contents for 5010.B


























Search results

Summary of Contents for 5010.B

Reviews:

Related manuals for 5010.B

Brands by name

Popular brands

Ronda 5010.B, Technical Instructions

Search results

Summary of Contents for 5010.B

Reviews:

Related manuals for 5010.B

Brands by name

Popular brands