Rona Collection 20035063 Operator'S Manual Download Page 8

ASSEMBLY INSTRUCTIONS

3

CARE AND MAINTENANCE

Glass: Wash and clean regularly using a non-abrasive neutral (PH balanced) glass cleaner. Light
scratches can be taken out by using a mild abrasive product. Rinse surface thoroughly afterward.
All spills should be cleaned immediately. Do not allow acidic substances, such as vinegar, to rest
on the glass surface as it will permanently cause a cloudy appearance. Avoid contact with oils, 
petroleum-based or caustic products.

Cabinet: Wipe dust frequently with a clean, soft, dry, lint-free cloth. Use only polishes that contain
detergents, emulsifiers and mineral oil. Avoid using silicone cleaners and waxes. Clean up excess
water and spills immediately. Water left over a long period of time will cause white spots in the 
finish.

C

D

E

F

3.   Drain assembly instructions:
 

   

 

   

3a. Remove tail piece (G) from drain body (C).
3b. Place flute washer (D) in such a direction as in 
 

   

the Figure 3

 

onto drain body (C) and carefully  

                 

      

  

 

  

      slide drain body (C) down through the drain 
      opening from the top of the sink.
3c. Under the sink, slide rubber washer (E) in such a 
      direction in the Figure 3. onto drain body (C).
      Secure drain body (C) to the sink with the nut (F).
      DO NOT OVER TIGHTEN.
3d. W

      HAND TIGHTEN ONLY.
3e. Once the complete drain assembly is installed,
      connect the tail piece (G) to the P-trap (not
      included) and test for leaks. NOTE: Tail piece (G)
      can be cut to length if needed.
3f. 

 

Install new or existing faucet (not included)

      according to the manufacturer's installation
      i nstructions.

-

-

IMPORTANT NOTE: The supplied drain must be 
used with this vanity sink.

G

4

4

D

   
   
   
   
   

   

   

8

rap the threads of the drain body (C) engaging 

      with the threads of the rail piece (G) with pipe 
      thread tape (not included) for minimum of 2 turns 
      and screw into drain body (C) . 

rawer  djustment instructions

:

In order to remove the drawer, press the white 
plastic parts to make them open and in the same 
time, pull out the drawer completely as in Image A.
To place the drawer back on glides, make sure 
both hooks are roperly inserted in the groove

Then push  the drawer completely in. There will b

tick” sound.

a

 

p

a “

Ima e  A

g

Ima e  B

g

Summary of Contents for Collection 20035063










Reviews: