Rona 38115088 Operator'S Manual Download Page 12

Page 12

IMPORTANT

1. Keep all children and pets away from assembly area. Children and pets should be 

supervised while gazebo is being assembled. 

:

2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction 

such as a fence, garage, house, overhanging branches, laundry lines or electrical wires. 

3. This unit is heavy. Do not assemble this item alone. Six people are recommended for 

safe assembly. 

4. Some parts may contain sharp edges. Wear protective gloves if necessary during 

assembly. 

5. When assembling and using this product, basic safety precautions should always be 

followed to reduce the risk of personal injury and damage to equipment. Please read all 

instructions before assembly and use. 

6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the 

gazebo in the ground. If you wish to secure the gazebo to a wood deck or concrete 

surface, use 16 anchors suited for these surfaces (anchors not included). 

7. Check all bolts for tightness before and during usage. 

8. Please check your state and local regulations prior to purchasing. Some jurisdictions 

may require permits for installation and use. Some special procedures may be valid in 

your area. 

9. While this gazebo is manufactured to withstand strong force winds through only the 

supplied ground stakes, 

securing the gazebo to a deck, concrete patio or a stronger base, 

in areas subject to frequent severe weather should be considered.

NOTE

: The gazebo’s roof and structure are not guaranteed against extreme weather 

conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow 

must be cleaned off regularly. Any damage caused by snow accumulation is not covered 

by the warranty. 

Our steel components for garden accessories and furniture are treated with rust inhibiting 

paint to protect it from rusting. However, due to the nature of steel, surface oxidation 

(rusting) will occur once these protective coatings are scratched. This is not considered a

defect and thus cannot be covered by the warranty. 

Care & Maintenance: 

To minimize this condition, we recommend care when assembling & handling the product 

to prevent scratching the paint. Should any scratching or damage occur, we recommend 

immediate touch-up with rust inhibiting paint. 

Surface rust can also be easily removed with a very light application of common cooking 

oil. If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the 

oxidation may drip on to the deck or patio and caused damaging stains, which may be 

difficult to remove. This can be prevented if the above-mentioned measures are taken to 

keep the product from oxidizing.

Summary of Contents for 38115088

























Reviews: