background image

 

 

                  

 

 

 

12. Technical Specification 

 
Size:    

 

34.7L x 13.3W x 10.2cmD (22.8cm including bracket) 

Power Rating:   

62 Watts maximum 

Voltage:  

 

220-240V~ or 110-120V~ 50/60Hz 

12VDC Output Current: 500mA maximum 
Light:    

 

40W LED Module 
Average LED Module life 100,000+ hours 

Weight:  

 

3.2kg 

Lumens:  

 

850 lumens (on screen) 

Colour :  

 

Colour temperature 4000° K 

Cooling: 

 

Tubeaxial fan 

Standard lens:  

3 element 85mm f2.8 42.5mm Helical Focus Groove 

Operating:  

 

Ambient temperature 10 to 35°C 
Relative humidity 80%rH max. 

Mains fuse: 

 

T1AH/250V ceramic (20mm x 5mm diameter) 

Control inputs: 

3.5mm mono or stereo jack plugs 

IP: 

 

 

IP 20 rating 

 

13. Installation 

 

 

Choose a suitable location for the projector, bearing in mind the following: 

 

 

Please seek advice from a suitably qualified electrician regarding the safe installation 
of this projector.  Installation requirements will very according to the zones of the 
water environment - please refer to the BS 7671: 2008+A3:2015 Requirements for 
Electrical Installations 17th Edition regulations (particularly point 702.55). It may be 
advisable to install this in a neighbouring room and project through a Perspex screen.  
Install indoors in dry environments only. 

 

This product requires one electrical socket. 

 

Make sure the projection will be onto a suitable surface – a surface free of objects 
and that is white or pale in colour. 

 

The projector is a visual product and should not be handled. However, you may wish 
to access the projector periodically to change effects. 

 

There must be unrestricted airflow around the projector, especially around the air 
inlet grille. 

 

If an extension cord is necessary, a cord with a current rating at least equal to that of 
the appliance must be used. Cords rated for less amperage than the appliance may 
overheat. 

 

The projector must always be connected to a grounded (earthed) electricity supply. 

 

Only connect to a power supply with a voltage corresponding to that printed on the 
projector.  Use the adapter fitting that is appropriate to the country where the 
projector is being used. 

 

Do not use the projector at an angle of more than 90° from horizontal as this may 
cause an effect or effect accessory to separate from the projector, fall and break 
which may also cause injury.  

Summary of Contents for 22126












Reviews: