Rolls-Royce Helicon X3 User Manual Download Page 103

Page: 103 / 140

Trouble Shooting

Page 7 of 16

Doc. No.: 13S000411
Revision: A

2.3

Steering Gear

The following alarms will be issued for steering gear related faults:

Alarm Text

Cause, Effect and Action

Failure steering gear

Cause: Steering gear failure

Effect: Steering gear locked in current position until “Reset “ is operated

Action: Check the reason for alarm on the frequency converter in steering gear
compartment. Reset the alarm in the control panel.

Warning steering gear

Cause: Warning something may be wrong with the steering gear

Effect: Depending on error code in frequency converter.

Action: Check the reason for alarm on the frequency converter in steering gear
compartment. Reset the alarm in the control panel.

High temperature steering
gear

Cause: The temperature in the steering gear is to high.

Effect:

Action: Check the reason for alarm on the frequency converter in steering gear
compartment. Reset the alarm in the control panel.

Summary of Contents for Helicon X3

















































































































Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands

Rolls-Royce Helicon X3, User Manual

Search results

Summary of Contents for Helicon X3

Reviews:

Related manuals for Helicon X3

Brands by name

Popular brands