background image

4

Rollerdor RD20X2SOM Somfy Rollixo Control Box,  Edition 2022/1

Pictures are for illustration purposes only, connector blocks are not provided and further fittings may be required. 

2. MOTOR DIRECTION OF          

ROTATION SETTING

At the same time press and hold the UP & DOWN buttons 
on the control  panel until the door moves forward AND 
backwards, then release the buttons – the controller is 
now in ‘motor adjustment mode’, the motor LED light will 
flash slowly. In motor adjustment mode, the Up & Down 
control buttons are in ‘hold to run’ mode - you must 
press and hold the button in to operate the door up and 
down.

 Press and hold the UP button to check the motor 
direction. If the motor direction is correct, move on 
to set the limits of the door. If the motor direction is 
incorrect, you can either swap the black and brown 
motor wires around or press and hold the STOP button 
until the door judders up and down > the direction has 
been reversed > check again and then move on to set 
the limits of the door.

3

4

2

1

Prog

STOP

3

4

2

1

Prog

STOP

Briefly press the PROG button until the door jogs to complete the motor 
set up procedure. The motor & safety brake LED goes out and the safety 
edge LED comes on.

Prog

Correct direction 
of rotation

Incorrect direction 
of rotation

1

3

2

Summary of Contents for RD20X2SOM












Reviews: