Press & quickly release button on motor head
*
PROCEED TO SETTING LIMITS
Press & hold button on
motor head * for 4secs
Power OFF for 5 seconds
& return to start and
reverse blind direction.
Check blind direction
OK
Power ON
IF POWER IS ALREADY ON
© 2016 Rollease Acmeda
PAIR RF401s WALL CONTROLLER TO EL MOTOR
Operation
Item
Item
Operation
Result
Illustration
Setup
bottom
limit
1
Keep pressing the
LIMIT
key on the
primary transmitter for
6 seconds above
The motor sounds
"KA
KA"
2
Release the key
The motor is under the
status of Limit setting
3
Press the
DOWN
key
on the transmitter
The motor runs down
4
When the motor is
running close to the
end-point of lower limit,
press
STOP
The motor stops running
5
Press either
UP
or
DOWN
key
The motor runs step by
step to adjust lower limit
accurately
6
Press
CONFIRM
key
on the transmitter
The motor sounds
"KA
KA"
, the setting has
complete.
Setup
upper limit
7
Press
UP
key on
primary transmitter
The motor runs up
8
When the motor is
running close to the
end-point of upper limit,
press
STOP
The motor stops running
9
Press either
UP
or
DOWN
The motor runs step by
step to adjust lower limit
accurately
10 Press
CONFIRM
key
on the transmitter
The motor sounds
"KA
KA"
, the setting has
complete.
Charging
The motor work with Li-ion battery, please have it charged when the motor stop working or work
faltering. Please plug the charger into the charger hole on the motor head, the charging time is
5 to 6 hours.
FAQ
If nothing works, please check:
●
if the motor does not working or works faltering, please charging the motor battery firstly
●
If the motor runs to a direction continually, the user didn't setup limit successfully, please re-set
limit.
For instructional purposes, the following options have been shown:
Easy-Lock Chain Winder 'AC' Installation Brackets.
Top Fix installation.
'AC' Bracket Cover Caps
40mm Motor - Somfy.
Somfy Drive & Crown Wheels.
INSTALLATION
ROLLER BLINDS
40mm MOTORISATION
ENSURE 'NOTCH' OF CROWN WHEEL
LOCKS WITHIN GAP OF MOTOR HEAD.
ASSEMBLY INSTRUCTIONS
STEP 1:
Install
Crown Wheel
onto
40mm Motor
. Ensure 'notch' of
Crown
Wheel
locks within gap of
Motor Head
.
STEP 2:
Install
Drive Wheel
onto
40mm Motor
.
NOTE:
* For Elero Motors, use 'O' ring supplied by Elero to lock
Drive Wheel
to
40mm Motor
.
* For Gaposa Motors, use
Gaposa Retaining Clip
to lock
Drive Wheel
to
40mm Motor
.
* For Selve Motors, use plastic retaining clip supplied by Selve to lock
Drive Wheel
to
40mm Motor
.
STEP 3:
Mount
40mm Motor Disk Adaptor
onto
Motor head
with
Counter
Sunk Screws
.
ONLY USE WITH GAPOSA
Page 57
=
Beep
+
OR
For instructional purposes, the following options have been shown:
Easy-Lock Chain Winder 'AC' Installation Brackets.
Top Fix installation.
'AC' Bracket Cover Caps
40mm Motor - Somfy.
Somfy Drive & Crown Wheels.
INSTALLATION
ROLLER BLINDS
40mm MOTORISATION
ENSURE 'NOTCH' OF CROWN WHEEL
LOCKS WITHIN GAP OF MOTOR HEAD.
ASSEMBLY INSTRUCTIONS
STEP 1:
Install
Crown Wheel
onto
40mm Motor
. Ensure 'notch' of
Crown
Wheel
locks within gap of
Motor Head
.
STEP 2:
Install
Drive Wheel
onto
40mm Motor
.
NOTE:
* For Elero Motors, use 'O' ring supplied by Elero to lock
Drive Wheel
to
40mm Motor
.
* For Gaposa Motors, use
Gaposa Retaining Clip
to lock
Drive Wheel
to
40mm Motor
.
* For Selve Motors, use plastic retaining clip supplied by Selve to lock
Drive Wheel
to
40mm Motor
.
STEP 3:
Mount
40mm Motor Disk Adaptor
onto
Motor head
with
Counter
Sunk Screws
.
ONLY USE WITH GAPOSA
Page 57
=
Beep
+
TO REVERSE
DIRECTION
OR
UP
TO REVERSE DIRECTION IF REQUIRED
=
P2 P2
within 4 seconds
within 4 seconds
Jog
Jog
© 2016 Rollease Acmeda
For instructional purposes, the following options have been shown:
Easy-Lock Chain Winder 'AC' Installation Brackets.
Top Fix installation.
'AC' Bracket Cover Caps
40mm Motor - Somfy.
Somfy Drive & Crown Wheels.
INSTALLATION
ROLLER BLINDS
40mm MOTORISATION
ENSURE 'NOTCH' OF CROWN WHEEL
LOCKS WITHIN GAP OF MOTOR HEAD.
ASSEMBLY INSTRUCTIONS
STEP 1:
Install
Crown Wheel
onto
40mm Motor
. Ensure 'notch' of
Crown
Wheel
locks within gap of
Motor Head
.
STEP 2:
Install
Drive Wheel
onto
40mm Motor
.
NOTE:
* For Elero Motors, use 'O' ring supplied by Elero to lock
Drive Wheel
to
40mm Motor
.
* For Gaposa Motors, use
Gaposa Retaining Clip
to lock
Drive Wheel
to
40mm Motor
.
* For Selve Motors, use plastic retaining clip supplied by Selve to lock
Drive Wheel
to
40mm Motor
.
STEP 3:
Mount
40mm Motor Disk Adaptor
onto
Motor head
with
Counter
Sunk Screws
.
ONLY USE WITH GAPOSA
Page 57
Page. 3 of 8
1
1
Cutting power before limit setting process is complete will result in loss of pairing.
To reset motor P2 + STOP + P2. Removes all emitters & deletes limits.
