Roland VR-4HD, Reference Manual

Page: 4 / 38

Menu List (Setup Screen)
4
Category Setting item Value Explanation
VIDEO OUT OUTPUT COLOR SPACE AUTO , RGB-FULL, RGB-LIMIT, YCbCr This sets the color space for HDMI OUT connector and RGB/COMPONENT output connector.
OUTPUT DVI-D/HDMI DVI-D, HDMI This sets the output mode of the HDMI OUT connector.
PREVIEW CONTRAST
-64–
0
–63 This adjusts the contrast of the preview output video.
PREVIEW SATURATION -64– 0 –63 This adjusts the saturation of the preview output video.
PREVIEW BRIGHTNESS -64– 0 –63 This adjusts the brightness of the preview output video.
PREVIEW COLOR SPACE AUTO
, RGB-FULL, RGB-LIMIT, YCbCr This sets the color space for PVW OUT connector.
PREVIEW DVI-D/HDMI DVI-D,
HDMI
This sets the output mode for PVW OUT connector.
OUTPUT FADE
BLACK
, WHITE, STILL
5
“BLACK” or “WHITE” specifies the fade color used during an output fade.
5
Setting this to “STILL” makes the [OUTPUT FADE] button function as a still-image output
button.
OUTPUT FADE WHITE LEVEL 0–
255
This adjusts the white level during output fade.
OUTPUT FADE BLACK LEVEL 0 –255 This adjusts the black level during output fade.
OUTPUT FADE AUDIO FLW OFF
, ON Setting this to “ON” enables the Audio Follow feature during output fade.
AUDIO
AUTO MIXING SW OFF , ON This switches the Auto Mixing feature on or off.
AUTO MIXING SETUP ([EDIT]) This displays the AUTO MIXING Screen (p. 6).
ECHO CANCEL SW OFF , ON This switches the Echo Cancel feature on or off.
ECHO CANCEL SETUP ([EDIT]) This displays the ECHO CANCEL Screen (p. 6).
AUDIO FOLLOW SW OFF , ON This switches the Audio Follow feature on or off.
AUDIO FOLLOW SETUP ([EDIT]) This displays the AUDIO FOLLOW Screen (p. 11).
Page 3/3
USER
The setting items are similar to those for “USER Button Settings” (p. 14).
MEMORY SAVE ([SETUP]) This displays the MEMORY SELECT Screen (p. 7).
LOAD ([SELECT]) This displays the MEMORY LOAD Screen (p. 7).
MANUAL MODE
OFF
, ON
This sets whether the state of the operation panel is updated (ON) or not updated (OFF)
when a memory is recalled.
POWER ON LOAD
OFF
, 1–8
Selecting a memory number causes the settings at the selected memory number to be
recalled at startup.
REMOTE
MIDI Rx CHANNEL 1
–16
This sets the receive channel for MIDI messages when operating the VR-4HD remotely using
an external MIDI device.
RS-232 OFF , ON Setting this to “ON” makes it possible to send and receive RS-232 commands.
BAUDRATE 9600, 19200, 38400, 115200 This sets the communication speed (bps) of the RS-232 connector.
GPI 1 TYPE
:
GPI 4 TYPE
N/A
, VIDEO CH SEL 1–4,
MEMORY LOAD 1–8,
USER 1–5
This sets the function assigned to the GPI channel.
N/A:
No function is assigned.
VIDEO CH SEL: This switches the video.
MEMORY LOAD: This loads a memory.
USER:
This performs the same operation as pressing the USER button.
* When a control signal is input from an external source, the assigned function is executed.
The GPI trigger is fixed at the trailing edge (low: ON).
For details, refer to “Inputting a Control Signal” (p. 22).
GPO 1 TYPE
:
GPO 4 TYPE
ONE SHOT , ALT
This sets the operation mode of the GPO channel.
ONE SHOT: This outputs a control signal for 1 second.
ALT:
This outputs a control signal using alternate operation.
* You can output a control signal by assigning a GPO channel (1–4) to a USER button, then
operating the USER button.
For details, refer to “Outputting a Control Signal” (p. 23).
SYSTEM
HDCP OFF , ON
When set to “ON,” copyright-protected (HDCP) video can be input. HDCP is also added to the
video that is output.
FRAME RATE
59.94 Hz
, 50 Hz
This sets the frame rate.
* For output via the USB 3.0 only, the frame rate when set to “59.94 Hz” is “29.97 Hz.”
Similarly, when set to “50 Hz,” the frame rate is “25 Hz.”
SYSTEM FORMAT 720p, 1080i, 1080p
This specifies the system format for the VR-4HD. The input and output formats of the
respective connectors are determined according to the system format, as shown in the table
below.
System
format
Input format (*2) Output format
Input connector:
HDMI IN 1–3
Output connector:
PVW OUT, HDMI OUT (*3),
RGB/COMPONENT (*3)
Output connector:
USB 3.0
720p 720p 720p 720p
1080i 1080i, 1080p 1080i
1080p
1080p 1080i, 1080p 1080p
(*2) For the channel 4 input connectors (HDMI IN 4, RGB/COMPONENT 4, and COMPOSITE 4),
you set the input format individually using “RESOLUTION (EDID)” (p. 2), irrespective
of the system format.
(*3) For the HDMI OUT connector and the RGB/COMPONENT output connector, you can
specify a desired output format by using “OUTPUT RESOLUTION” (p. 3).
The system format setting is followed only when “OUTPUT RESOLUTION” is set to “AUTO.”