VIMA JM-8
r
161
●
Cyclically modulates the volume to add tremolo effect to the
sound.
●
Modulation Wave (TRI, SQR, SIN, SAW1, SAW2)—Modulation
Wave. TRI: triangle wave, SQR: square wave, SIN: sine wave,
SAW1/2: sawtooth wave.
●
Rate [sync] (Hz, Note)—Use this parameter to specify whether
●
Rate [Hz] (0.05~10.00Hz)—Frequency, i.e. modulation speed.
●
Rate [note] (musical notes)—Rate parameters can be set as a
●
Depth (0~127)—Depth to which the effect is applied.
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
●
EQ High Gain (–15dB~0~15dB)—Gain of the high frequency
●
Cyclically modulates the stereo location of the sound.
●
Modulation Wave (TRI, SQR, SIN, SAW1, SAW2)—Modulation
Wave. TRI: triangle wave, SQR: square wave, SIN: sine wave,
SAW1/2: sawtooth wave.
●
Rate [sync] (Hz, Note)—Use this parameter to specify whether
●
Rate [Hz] (0.05~10.00Hz)—Frequency, i.e. modulation speed.
●
Rate [note] (musical notes)—Rate parameters can be set as a
●
Depth (0~127)—Depth to which the effect is applied.
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
●
EQ High Gain (–15dB~0~15dB)—Gain of the high frequency
●
This uses a 16-step sequence to vary the panning of the sound.
●
Step 1~16 (L64~0~63R)—Pan at each step.
●
Rate [sync] (Hz, Note)—Use this parameter to specify whether
●
Rate [Hz] (0.05~10.00Hz)—Rate at which the 16-step sequence
●
Rate [note] (musical notes)—Rate parameters can be set as a
●
Attack (0~127)—Speed at which the pan changes between steps.
●
Input Sync Sw (Off, On)—Specifies whether an input note will
cause the sequence to resume from the first step of the
sequence (ON) or not (OFF).
●
Input Sync Threshold (0~127)—Volume at which an input note
will be detected.
●
By applying successive cuts to the sound, this effect turns a
conventional sound into a sound that appears to be played as
a backing phrase. This is especially effective when applied to
sustain-type sounds.
●
Step 1~16 (0~127)—Level at each step.
●
Rate [sync] (Hz, Note)—Use this parameter to specify whether
●
Rate [Hz] (0.05~10.00Hz)—Rate at which the 16-step sequence
●
Rate [note] (musical notes)—Rate parameters can be set as a
●
Attack (0~127)—Speed at which the level changes between
steps.
●
Input Sync Sw (Off, On)—Specifies whether an input note will
cause the sequence to resume from the first step of the
sequence (ON) or not (OFF).
●
Input Sync Threshold (0~127)—Volume at which an input note
●
Mode (Legato, Slash)—Sets the manner in which the volume
changes as one step progresses to the next.
LEGATO: The change in volume from one step’s level to the next
remains unaltered. If the level of a following step is the same as
the one preceding it, there is no change in volume.
SLASH: The level is momentarily set to 0 before progressing to
the level of the next step. This change in volume occurs even if
the level of the following step is the same as the preceding step.
●
Shuffle (0~127)—Timing of volume changes in levels for even-
numbered steps (step 2, step 4, step 6…). The higher the value,
the later the beat progresses.
●
This type provides modified response for the rotary speaker,
with the low end boosted further.
This effect features the same specifications as the VK-7’s built-in
rotary speaker.
●
Speed (Slow, Fast)—Rotational speed of the rotating speaker.
●
Brake (Off, On)—Switches the rotation of the rotary speaker.
When this is turned on, the rotation will gradually stop. When it
is turned off, the rotation will gradually resume.
●
Woofer Slow Speed (0.05~10.0Hz)—Low-speed rotation speed
of the woofer.
●
Woofer Fast Speed (0.05~10.0Hz)—High-speed rotation speed
of the woofer.
●
Woofer Trans Up (0~127)—Adjusts the rate at which the woofer
rotation speeds up when the rotation is switched from Slow to
Fast.
●
Woofer Trans Down (0~127)—Adjusts the rate at which the
woofer rotation slows down when the rotation is switched from
Fast to Slow.
●
Woofer Level (0~127)—Volume of the woofer.
●
Tweeter Slow Speed (0.05~10.0Hz)—Low-speed rotation speed
of the tweeter.
●
Tweeter Fast Speed (0.05~10.0Hz)—High-speed rotation speed
of the tweeter.
●
Tweeter Trans Up (0~127)—Adjusts the rate at which the
tweeter rotation speeds up when the rotation is switched from
Slow to Fast.
●
Tweeter Trans Down (0~127)—Adjusts the rate at which the
tweeter rotation slows down when the rotation is switched
from Fast to Slow.
●
Tweeter Level (0~127)—Volume of the tweeter.
●
Spread (0~10)—Sets the rotary speaker stereo image. The higher
the value set, the wider the sound is spread out.
●
EQ Low Gain (–15dB~0~15dB)—Gain of the low frequency
●
EQ High Gain (–15dB~0~15dB)—Gain of the high frequency
●
This applies a 3D effect to the chorus sound. The chorus sound
will be positioned 90 degrees left and 90 degrees right.
●
Filter Type (OFF, LPF, HPF)—Type of filter. OFF: no filter is used.
JM-8_OM_GB.book Page 161 Wednesday, July 29, 2009 4:43 PM
Summary of Contents for VIMA JM-8
Page 1: ...r Owner s Manual JM 8_OM_GB book Page 1 Wednesday July 29 2009 4 43 PM ...
Page 174: ...174 rVIMA JM 8 JM 8_OM_GB book Page 174 Wednesday July 29 2009 4 43 PM ...
Page 175: ...For EU Countries For China For China JM 8_OM_GB book Page 175 Wednesday July 29 2009 4 43 PM ...
Page 176: ...R 602 00 0323 01 RES 736 09 JM 8 OM E JM 8 Cov 3 4 GB Page 176 Thursday July 30 2009 10 30 AM ...
