background image

 

7

 

USING THE UNIT SAFELY

1.

 

Loosen the stand’s anchor bolts and remove 

the foot plate.

 

fig.KD-Assy06

 

2.

 

Set the kick pedal so that the entire bottom 

surface is attached to the floor.

 

3.

 

In most cases, the stand becomes somewhat 

floated. Tighten the anchor bolts securely there 

to fix the stand and foot plate.

 

fig.KD-Assy07.e

 

• Install the kick pedal securely.

• Take care not to pinch your fingers.

• The tips of the anchor bolts are sharp. Handle with care.

• When moving the setup, be sure to remove the screws 

and fold the stand. Transporting the KD-8 while it 
remains open may subject the stand to excessive strain 
and result in damage to the stand.

 

Adjusting the Anchor Bolts

 

When using the kick pedal on a drum mat or similar surface, 
adjust the anchor bolts so their tips protrude from the plate 
and secure the pedal in place; this will make it easier to use the 
kick pedal.

However, when used on flooring, the anchor bolts may 
damage the floor. Adjust the anchor bolts correctly.

 

fig.KD-Anchor.e

 

The tips of the anchor bolts are sharp. Handle with care.

 

When Using a Twin Pedal

 

fig.KD-Pedal1

 

Position the two beaters 
equally apart from the center 
of the pad as shown in the 
figure at left. If one of the 
beater is further away from the 
center than the other, the 
sound from the further beater 
will be lower in volume, or 
will not sound as desired.

 

fig.KD-Pedal2

 

Using a twin pedal will result 
in lower sensitivity as 
compared to when a single 
pedal is used. Raise the 
sensitivity on the sound 
module.

 

KD-8

 

Dimensions:

272 (W) x 260 (D) x 405 (H) mm

10-3/4 (W) x 10-1/4 (D) x 16 (H) inches

Weight:

2.9 kg 
6 lbs 7 oz

Accessories:

Screws

 

962a

 

* In the interest of product improvement, the specifications and/

or appearance of this unit are subject to change without prior 
notice.

 

add

 

* Continuous playing may cause dis-coloration of the pad, but 

this will not affect the Pad's function.

This hight will vary depending 
on your kick pedal.

 

Specifications

When Using on the Drum Mat

When using on the Floor

Adjusting the Anchor Bolts

TD-6KX_e 7 ページ 2007年6月20日 水曜日 午前11時29分

Summary of Contents for V-Drums TD-6KX





















Reviews: