background image

MIDI Implementation

4

❍ ■

RPN MSB/LSB (Controller number 101, 100)

Status 

2nd byte 

3rd byte

BnH 

65H 

mmH

BnH 

64H 

llH

n = MIDI channel number: 

0H - FH (ch.1 - 16)

mm = upper byte of parameter number specified by RPN(MSB)
ll = lower byte of parameter number specified by RPN(LSB)

<< RPN >>

Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any 
order) should be sent in order to select the parameter, then Data Entry (Controller 
numbers 6 and 38) should be sent to set the value.
Once RPN messages are received, Data Entry messages that is received at the same 
MIDI channel after that are recognized as changing toward the value of the RPN 
messages. In order not to make any mistakes, transmitting RPN Null is recommended 
after setting parameters you need.
Refer to “Examples of actual MIDI message <Example 4>” (p. 12).

This device receives the following RPNs.

RPN

Data Entry

MSB, LSB

MSB, LSB

Explanation                                                                            

00H, 00H

mmH, —

Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
specify up to 2 octaves in semitone steps

7FH, 7FH

—, —

RPN null
mm,ll: ignored
set condition where RPN is unspecified. 
The Data Entry messages after set RPN 
null will be ignored.
(No Data Entry messages are required 
after RPN null).
Settings already made will not change.

*  Only the channels assigned to the backing part can be received.
*  Changes the bend range ([PATTERN] - [PART] - [BACKING] Bend Range) for the part. 

Not indicated in the display.

*  Not recorded in the sequencer.

●■

Program Change

Status 

2nd byte

CnH 

ppH

n = MIDI channel number: 

0H - FH (ch.1 - 16)

pp = Program number: 

00H - 7FH (prog.1 - prog.128)

*  Not Received when [SETUP] - [MIDI] - [PROG] RX Switch is set to “OFF.”
*  The sound will change beginning with the next Note-On after the Program Change 

is received. Voices which were already sounding before the Program Change was 
received will not be affected.

*  Only the program number set with [SETUP] - [MIDI] - [PROG] - [DRM KIT] is received 

on the channel assigned to the drum part.

*  Only the program number set with [SETUP] - [MIDI] - [PROG] - [PRC SET] is received 

on the channel assigned to the percussion part.

*  For more on the channels assigned to backing parts, refer to the “Backing 

Instrument List” in the Data List. Specify sounds using a combination of these three 
messages: the MSB and LSB of the Bank Select, and the Program Change.

*  Not recorded in the sequencer.

●■

Pitch Bend Change

Status 

2nd byte 

3rd byte

EnH 

llH 

mmH

n = MIDI channel number: 

0H - FH (ch.1 - 16)

mm, ll = Pitch Bend value: 

00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

*  Only the channels assigned to the backing part can be received.
*  When recording, this is recorded in the sequencer data itself.

■ ■

Channel Mode Messages

*  Following Channel Voice Messages can be received in [SETUP] - [MIDI] - [MIDI CH] Tx/

Rx Channel.

*  Not received when [SETUP] - [MIDI] - [MIDI CH] Tx/Rx Switch is set to “OFF.”

●■

All Sounds Off (Controller number 120)

Status 

2nd byte 

3rd byte

BnH 

78H 

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*  When this message is received, all currently-sounding notes on the corresponding 

channel will be silenced. However, the status of channel messages will not change. 

*  When recording, this is recorded in the sequencer data itself.

Summary of Contents for V-Drums TD-30
















Reviews: