background image

 

Ã

Set the snare (PD-140DS), the ride cymbal (CY-18DR) and the hi-hat (VH-14D)

1. 

Use the cursor buttons to select “OK”, and press [ENTER] button.

2. 

Use the cursor buttons to select “PD140DS”, “CY18DR”, or “VH14D”.

3. 

Use the dial to specify the Assign.

*  You can’t specify the same assignment multiple times.

The first time you connect the PD-140DS, CY-18DR and VH-14D to the DIGITAL TRIGGER IN port, 

the following screen will appear. As directed in the screen, assign the PD-140DS as snare, assign 

the CY-18DR as ride, and assign the VH-14D as hi-hat.

*  If you specify the same trigger input as a pad that is connected to a dedicated connection cable or TRIGGER IN 

jack, the pad that’s connected to that TRIGGER INPUT jack and TRIGGER IN jack won’t produce sound.

Pad

Assign

PD140DS

SNARE

CY18DR

RIDE

VH14D

HI-HAT

Setting example

4. 

Press the [DRUM KIT] button to return to the DRUM KIT screen.

This completes settings.

 

Ã

When you’ve finished making connections, turn on the power as described in “TD-27 Quick Start”, and verify that you 

can hear sound.

This completes assembly and connections.

USING THE UNIT SAFELY

IMPORTANT NOTES

Connect the pads to the  
drum sound module

6

Connection procedure

*  To prevent malfunction and equipment failure, always turn down the volume, and turn off all the units 

before making any connections.

1. 

Connect the dedicated connection cable 

to the TRIGGER INPUT connector on the 

bottom panel of the drum sound module.

Insert the connector all the way, then turn the 
knobs to fasten it securely. 

Knob

2. 

Labels indicating the pad to be connected 

are attached to the cable. Connect the 

cable to the OUTPUT jack of each pad as 

shown in the illustration at right.

3. 

Using the included trigger cable, connect 

crash 2 to the CRASH 2 jack of the TRIGGER 

IN jack on the back panel of the drum 

sound module.

Drum sound module side

Cymbal side

4. 

Using the included connection cables, 

connect the snare (PD-140DS), ride 

(CY-18DR) and hi-hat (VH-14D) to the 

DIGITAL TRIGGER IN ports of the drum 

sound module.

*  You may connect to any of the ports 1–3.

Fasten the cables so that they will not obstruct 

your playing; use cable clips and cable ties. 

Make sure to wrap the cable ties around the 

pipes.

*  Insert the plug firmly, 

making sure it’s all the 

way in.

As seen from the back of TD-27KV2

T1

T3

KIK

T2

CR1

Dedicated connection cable

Trigger cable (Crash 2)

Connection cable (Snare, Ride, Hi-hat)

KIK

Labels attached to the end of the cable

Crash 2

Ride

Snare

TD-27

CR1

7

Connect the AC adaptor 
and speakers

*  To prevent malfunction and equipment failure, always turn down the volume, 

and turn off all the units before making any connections.

Connect the AC adaptor, headphones, or speakers.

*  Use the cord hook located on the bottom of the unit to secure the AC 

adaptor cord as shown in the illustration.

Cord 

Hook

The cord of 

the supplied 

AC Adaptor

AC outlet

 WARNING

Use only the stand that is recommended

This unit should be used only with a stand 

(MDS-Standard 2) that is recommended by Roland.

Do not place in a location that is unstable

When using the unit with a stand (MDS-Standard 2) 

recommended by Roland, the stand must be carefully 

placed so it is level and sure to remain stable. If not using 

a stand, you still need to make sure that any location you choose 

for placing the unit provides a level surface that will properly 

support the unit, and keep it from wobbling.

Precautions regarding placement of this unit on a 

stand

Be sure to follow the instructions in the Owner’s Manual 

carefully when placing this unit on a stand (Refer to “TD-27KV2 

Setup Guide”).
If it is not set up properly, you risk creating an unstable situation 

which could lead to the unit falling or the stand toppling, and 

may result in injury.

 WARNING

Be cautious to protect children from injury

Always make sure that an adult is on hand to provide 

supervision and guidance when using the unit in places 

where children are present, or when a child will be using 

the unit.

Take care not to get burned

Otherwise, you risk causing damage or malfunction.

 CAUTION

Use only the specified stand(s)

This unit is designed to be used in combination with 

specific stands (MDS-Standard 2) manufactured by 

Roland. If used in combination with other stands, you 

risk sustaining injuries as the result of this product dropping 

down or toppling over due to a lack of stability.

Additional Precautions

• 

Use a reasonable amount of care when using the unit’s sensors; 

and when using its jacks and connectors. Rough handling can 

lead to malfunctions.

• 

This instrument is designed to minimize the extraneous sounds 

produced when it’s played. However, since sound vibrations 

can be transmitted through floors and walls to a greater degree 

than expected, take care not to allow these sounds to become 

a nuisance others nearby.

• 

This document explains the specifications of the product at the 

time that the document was issued. For the latest information, 

refer to the Roland website.

Intellectual Property Right

• 

It is forbidden by law to make an audio recording, video 

recording, copy or revision of a third party’s copyrighted work 

(musical work, video work, broadcast, live performance, or 

other work), whether in whole or in part, and distribute, sell, 

lease, perform, or broadcast it without the permission of the 

copyright owner.

• 

Do not use this product for purposes that could infringe on a 

copyright held by a third party. We assume no responsibility 

whatsoever with regard to any infringements of third-party 

copyrights arising through your use of this product.

• 

The copyright of content in this product (the sound waveform 

data, style data, accompaniment patterns, phrase data, audio 

loops and image data) is reserved by Roland Corporation.

• 

Purchasers of this product are permitted to utilize said content 

(except song data such as Demo Songs) for the creating, 

performing, recording and distributing original musical works.

• 

Purchasers of this product are NOT permitted to extract 

said content in original or modified form, for the purpose of 

distributing recorded medium of said content or making them 

available on a computer network.

• 

The SD logo 

 and SDHC logo 

 are trademarks of SD-

3C, LLC.

• 

ASIO is a trademark and software of Steinberg Media 

Technologies GmbH.

• 

This product contains eParts integrated software platform of 

eSOL Co.,Ltd. eParts is a trademark of eSOL Co., Ltd. in Japan.

• 

The 

Bluetooth®

 word mark and logos are registered trademarks 

owned by Bluetooth SIG, Inc. and any use of such marks by 

Roland is under license.

• 

This Product uses the Source Code of μT-Kernel under T-License 

2.0 granted by the T-Engine Forum (www.tron.org).

• 

Roland, BOSS, and V-Drums are either registered trademarks or 

trademarks of Roland Corporation in the United States and/or 

other countries.

• 

Company names and product names appearing in this 

document are registered trademarks or trademarks of their 

respective owners.

About       WARNING and       CAUTION Notices

Used for instructions intended to alert the 

user to the risk of injury or material 

damage should the unit be used 

improperly. 
* Material damage refers to damage or 

other adverse effects caused with 

respect to the home and all its 

furnishings, as well to domestic animals 

or pets. 

Used for instructions intended to alert the 

user to the risk of death or severe injury 

should the unit be used improperly. 

The       symbol alerts the user to things that must be 

carried out. The specific thing that must be done is 

indicated by the design contained within the circle. In the 

case of the symbol at left, it means that the power-cord 

plug must be unplugged from the outlet. 

The       symbol alerts the user to important instructions or 

warnings.The specific meaning of the symbol is 

determined by the design contained within the triangle. In 

the case of the symbol at left, it is used for general 

cautions, warnings, or alerts to danger. 
The       symbol alerts the user to items that must never be 

carried out (are forbidden). The specific thing that must 

not be done is indicated by the design contained within 

the circle. In the case of the symbol at left, it means that 

the unit must never be disassembled. 

About the Symbols

ALWAYS OBSERVE THE FOLLOWING

 CAUTION

Evaluate safety issues before using stands

Even if you observe the cautions given in the owner’s 

manual, certain types of handling may allow this product 

to fall from the stand, or cause the stand to overturn. 

Please be mindful of any safety issues before using this product.

Avoid climbing on top of the unit, or placing heavy 

objects on it

Otherwise, you risk injury as the result of the unit 

toppling over or dropping down.

Disconnect all cords/cables before moving the unit

Damage or malfunction may result if you fail to 

disconnect all cables before moving the unit.

Cautions when moving this unit

If you need to move the instrument, at least two persons 

are required to safely lift and move the unit. It should be 

handled carefully, all the while keeping it level.

Take care so as not to get fingers pinched

When handling the following moving parts, take care 

so as not to get fingers, etc., pinched. An adult should 

always be in charge of handling these items.

• 

Stands

• 

Pedals

Keep small items out of the reach of children

To prevent accidental ingestion of the parts listed below, 

always keep them out of the reach of small children.

Included Parts:

• 

Cable clip 

• 

Cable tie

Removable Parts:

• 

Screws

• 

Washers

• 

Nuts

• 

Felt washers

• 

Wing bolts

• 

Drum key

• 

Springs

• 

Hand knobs

Figure A: Setting for a Left-Handed Player

Curve pipe R

Cymbal mount

Pad mount

Assembly for a Left-Handed Player

The settings explained in this guide are for a right-handed player. If you want to set up for a left-handed player, assemble the 
drum stand according to the procedure described in “Assembling the stand for a left-handed player” in the “MDS-Standard 2 
Owner’s Manual”. Also, install the pads as shown in the Figure A.

 

¹

Connect the cables to the OUTPUT jack of each pad as shown in the Figure B.

 

¹

Using the included trigger cable, connect crash 2 to the CRASH 2 jack of the drum sound module.

Figure B: As seen from the back of TD-27KV2

T1

T3

KIK

T2

CR1

Ride

Crash 2

Snare

TD-27

Hi-hat

Hi-hat

 

Ã

Adjust the hi-hat (VH-14D)

When using the VH-14D, be sure to adjust the offset and hi-hat on the TD-27 after connecting.
This adjustment is required in order to correctly detect open, close, and pedal operations.

NOTE

*  Continuous playing may cause dis-coloration of the pad, but this will not 

affect the Pad’s function.

*  See the VH-14D Owner’s Manual for details on the hi-hat.

Fixing the cables

Secure the cable in place 
with the cable tie

Leave some slack in 

the cable

Be sure to make this 
small plastic hook 

visible from 

you.

Wind a cable tie around the 
pipe and tighten it in order 
not to slip.

Wind a cable tie around a 
cable.

Insert the small plastic 
hook to a hole to secure 
the cable to the cymbal 
arm.

1. 

Press the [SYSTEM] button.

2. 

Use the cursor buttons to select “TRIGGER”, and 

then press the [ENTER] button.

3. 

Use the cursor buttons to select “HI-HAT”, and 

then press the [ENTER] button.

The TRIGGER HI-HAT screen appears.

*  “VH-14D” is not shown as a Trig Type when the VH-14D is 

not connected or if it is not assigned as the hi-hat. In this 

case, connect the VH-14D and assign it as the hi-hat.

4. 

Press the [F5] (OFFSET) button.

The VH OFFEST ADJUSTMENT screen appears.

5. 

Loosen the clutch screw of the top cymbal and 

let it sit on the bottom cymbal.

*  Do NOT touch the hi-hats or the pedal.

Clutch screw

6. 

Press the [F5] (EXECUTE) button.

The “VH Offset” parameter is set automatically 
(approx. 3 seconds).

7. 

Press the [KIT] button to return to the DRUM 

KIT screen.

Adjusting the offset

Adjusting the hi-hat

1. 

Adjust the gap between the top cymbal and bottom 

cymbal to a clearance of approximately 10 mm, then 

tighten the clutch screw.

Clutch screw

10 mm

*  Although the gap can be adjusted to a clearance that makes 

playing the hi-hat easier, setting too narrow or wide a gap can cause 
improper function of the unit and prevent the hi-hat from sounding 
as you intend. Setting the gap to 10 mm provides the most natural 
feel when playing the VH-14D.

2. 

Change the spring tension by adjusting the hi-hat 

stand.

For instructions on adjusting the tension, refer to the 
owner’s manual for your hi-hat stand.

*  If the spring tension is too high or too low, the hi-hat may not 

operate correctly and you might not be able to play the way you 
intended.

*  The tension may not be adjustable on some stands.

Reviews: