40
Chapter 2. Using Effects
*
1:
For effect types 43–45, you can hold down [FUNC] and press [F2] (SUB) to access a sub-parameter screen. The tables shown
below list the parameters that appear in these screens. Press [F3] (EXIT) to return to the previous screen.
*
2:
Available note values for synchronization (In the case of delay time, the result cannot exceed approximately three seconds.)
32nd note(
), 16th note(
), 8th note triplet(
), dotted 16th note(
), 8th note(
), quarter note triplet(
), dotted
8th note(
), quarter note(
), half note triplet(
), dotted quarter note(
), half note(
), dotted half note(
), whole
note(
)
43 SUBSONIC
Value
Explanation
E.LEVEL
0–127
Adjusts the volume of the effect sound.
PITCH
0–127
Adjusts the frequency of the sine wave.
ATTACK
0–127
Adjusts the time from when the source exceeds the threshold until the sine wave is heard.
44 OSCILLATOR(PAD)
Value
Explanation
EFFECT LEVEL
0–127
Adjusts the volume of the effect sound.
PAD1 KEY
C- –G9
Adjusts the key sounded by the oscillator when you press PAD 1.
LFO RATE
0–127
An LFO is an oscillator used to apply modulation; by increasing the vibrato or PWM you
can modulate the pitch or tone in a variety of ways.
LFO WAVE
SAW,
TRI,
SQR,
S-H
OSC TUNE
-24–+24
Specifies the coarse tuning (semitone steps) of the oscillator pitch.
OSC VIB DEPTH
0–127
Adjusts the depth of vibrato (using the LFO to cyclically modulate the pitch) for the oscil-
lator.
OSC XMOD
0–127
Adjusts the depth of cross modulation (using the SUB OSC to modulate the pitch of the
oscillator).
OSC LEVEL
0–127
Adjusts the volume of OSC.
SUB OSC WAVE
SAW,
TRI,
PLS1–9
Selects the SUB OSC waveform. (The choices are the same as for OSC WAVE on p. 39)
SUB OSC TUNE
-24–+24
Adjusts the coarse tuning (semitone steps) of the SUB OSC pitch.
SUB OSC VIB DEPT
0–127
Adjusts the depth of vibrato (using the LFO to cyclically modulate the pitch) for the SUB
OSC.
SUB OSC LEVEL
0–127
Adjusts the SUB OSC volume.
RING SRC1
OSC,
SUB
OSC,
NOISE,
MFX IN
Selects the two inputs for the ring modulator.
(
MFX IN
: MFX input source)
RING SRC2
RING LEVEL
0–127
Adjusts the volume of the ring modulator.
NOISE LEVEL
0–127
Adjusts the volume of the noise generator.
PORTA TIME
0–100
Adjusts the time over which pitch change will occur for the portamento effect (which cre-
ates smooth transitions between pitches).
45 ENVELOPER(PAD)
Value
Explanation
ATTACK
0–127
Adjusts the time from when you release the pad until the volume falls to the minimum.
FILTER TYPE
LP (-12),
BP (-12),
HP (-12),
LP (-24),
BP (-24),
HP (-24)
Low pass filter with a -12 dB slope
Band pass filter with a -12 dB slope
High pass filter with a -12 dB slope
Low pass filter with a -24 dB slope
Band pass filter with a -24 dB slope
High pass filter with a -24dB slope
TRI
(Triangle wave)
SQR
(Square wave)
SAW
(Sawtooth wave)
S-H
(Sample & Hold wave)
SP-606_e.book 40 ページ ２００４年６月２１日 月曜日 午前１０時８分
