Settings for the Entire Unit
25
Parameter
[1] knob
Value
[2] knob
Explanation
PEDAL Func
Hold Source
SCENE, SYS
Specifies whether the function assigned to the
pedal connected to the HOLD jack follows the
setting of the currently selected scene (SCENE)
or the system setting (SYS).
Hold
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the pedal
connected to the HOLD jack.
Hold Pole
STANDARD,
REVERSE
Specifies the polarity of the pedal connected
to the HOLD jack.
Ctrl Source
SCENE, SYS
Specifies whether the function assigned to the
pedal connected to the CTRL jack follows the
setting of the currently selected scene (SCENE)
or the system setting (SYS).
Ctrl
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the pedal
connected to the CTRL jack.
WHEEL Func
Wheel1 Source
SCENE, SYS
Specifies whether the function assigned to
the Wheel1 wheel follows the setting of the
currently selected scene (SCENE) or the system
setting (SYS).
Wheel1
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the Wheel1
wheel.
Wheel2 Source
SCENE, SYS
Specifies whether the function assigned to
the Wheel2 wheel follows the setting of the
currently selected scene (SCENE) or the system
setting (SYS).
Wheel2
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the Wheel2
wheel.
PART Btn Asgn
1-5
1-5+(S)
6-10
6-10+(S)
11-15
11-15+(S)
No Assign,
PartSel,
Part+KeySw,
KeySw, PartSw,
ArpSw, EfxSw
Assign the functions of the [1]–[5] ([6]–[10],
[11]–[15]) buttons and their functions when
pressed while holding down the [SHIFT]
button.
No Assign:
No assignment.
PartSel:
Specifies the current part operated
from the panel and in the screen. The part
played from the keyboard does not change.
Part+KeySw:
Simultaneously operates the
current part and the Keyboard SW, so that the
selected part can be played from the keyboard.
By pressing multiple parts simultaneously, you
can turn Keyboard SW on for multiple parts.
KeySw:
Functions as the keyboard switch to
change the part played from the keyboard.
PartSw:
Turns on/off the sound of each part.
This is useful for DJ-like performances in which
you turn each part’s sound on/off while you
perform.
ArpSw:
Switches whether each part is played
by the arpeggio.
Efx Sw:
From the left button, turns MFX, DRIVE,
REV, DLY, and CHO respectively on/off for all
parts simultaneously.
Parameter
[1] knob
Value
[2] knob
Explanation
CompAttack
0.1, 1, 2,... 100
[ms]
Specifies the time from when the input to the
mic compressor exceeds the Comp Thres level
until the volume is compressed.
CompRelease
10, 10, … 1000
[ms]
Specifies the time from when the input to the
mic compressor falls below the Comp Thres
level until compression is no longer applied.
CompThreshold
-60–0 [dB]
Specifies the level at which the mic compressor
starts applying compression.
CompRatio
1: 1, 2: 1, …4: 1,
8: 1, 16: 1, 32: 1,
INF: 1
Specifies the compression ratio for the mic
compressor.
CompKnee
0–30 [dB]
Smooths the transition until the mic
compressor starts to be applied.
Higher values produce a smoother transition.
CompOutGain
-24.0, -23.5, … 0,
…, +24.0 [dB]
Specifies the output volume of the mic
compressor.
Rev Send Lev
0–127
Specifies the amount of reverb that is applied
to the mic input.
Cho Send Lev
0–127
Specifies the amount of chorus that is applied
to the mic input.
Dly Send Lev
0–127
Specifies the amount of delay that is applied to
the mic input.
Mic Thru
OFF, ON
If you want the mic to be cut when the vocoder
is off, turn this “OFF.”
CONTROLLER
Velocity
REAL, 1–127
Specifies the velocity value that is transmitted
when you play the keyboard.
Velo Crv
LIGHT, MEDIUM,
HEAVY
Specifies the keyboard touch.
Velo Offset
-10–+9
Adjusts the keyboard velocity curve.
Knob Mode
DIRECT, CATCH
Specifies whether the parameter value
corresponding to a controller is immediately
updated when you operate that controller
(DIRECT) or only after the controller reaches
the same position as the parameter’s current
value (CATCH).
Aft Sens
0–100
Specifies the sensitivity of aftertouch.
BUTTON Func
Source
SCENE, SYS
Specifies whether the functions assigned
to these buttons follows the settings of the
currently selected scene (SCENE) or the system
settings (SYS).
S1 Func
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the S1
button.
S1 Mode
LATCH,
MOMENTARY
Specifies how the button operates.
S2 Func
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the S2
button.
S2 Mode
LATCH,
MOMENTARY
Specifies how the button operates.
S3 Func
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the S3
button.
S3 Mode
LATCH,
MOMENTARY
Specifies how the button operates.
SLIDER Func
SL1 Source
SCENE, SYS
Specifies whether the function assigned to the
SL1 slider follows the setting of the currently
selected scene (SCENE) or the system setting
(SYS).
SL1
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the SL1
slider.
SL2 Source
SCENE, SYS
Specifies whether the function assigned to the
SL2 slider follows the setting of the currently
selected scene (SCENE) or the system setting
(SYS).
SL2
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the SL2
slider.
