55
Chapter 5 Using Pedals to Control the Effects
Chapter
5
3.
Press [EXIT] to return to the Play screen.
Setting the Operation of External
Foot Switches (Sub CTL 1, 2 Function)
This sets the functioning of foot switches connected to the
SUB EXP PEDAL/SUB CTL1,2 jack on the rear panel as
“Subcontroller 1” and “Subcontroller 2.”
* When connecting an FS-6 (dual foot switch), it functions with
pedal switch B as Subcontroller 1 and pedal switch A as
Subcontroller 2.
* When two foot switches are connected using the special PCS-
31 connector cable (manufactured by Roland; optional), the
foot switch connected to the white-ringed plug functions as
Subcontroller 1 and the foot switch connected to the red-ringed
plug functions as Subcontroller 2.
* When connecting only one foot switch, only the Subcontroller
1 settings are enabled.
fig.05-009
1.
Press [SYSTEM], then press PARAMETER [
]
[
] so that “SubCTL1 Func” or “SubCTL2 Func” is
displayed.
fig.05-030d
2.
Use the PATCH/VALUE dial to set the function of the
foot switch.
3.
Press [EXIT] to return to the Play screen.
Value
Explanation
Auto
The pedal normally is used as a “foot vol-
ume” pedal. When Pedal Wah (p. 34) or
Pedal Bend (p. 45) is switched on, the EXP
pedal then automatically functions as a
“pedal wah” or “pedal bend” pedal.
When Pedal Wah and Pedal Bend are switched off, this automatical-
ly functions as a “foot volume” pedal.
Assignable
The pedal is used as the controller set in As-
sign (p. 56, p. 57) for each patch.
Foot Volume
The pedal functions as a “foot volume” pedal.
Patch Level
The pedal is used as the patch level controller.
Pedal Wah
The pedal is used as a “pedal wah” pedal
when Pedal Wah is switched on.
Pedal Bend
The pedal is used as a “pedal bend” pedal
when Pedal Bend is switched on.
1
2
1
3
Value
Explanation
Assignable
The pedal functions as the type of controller
set with Assign (p. 56, p. 57) in each individ-
ual patch.
Preamp Ch A/B
Switches between Preamp channel A and B.
Solo On/Off
Switches the Preamp SOLO on and off.
FX-1 On/Off
Switches the FX-1 on and off.
Comp On/Off
Switches the COMP on and off.
Wah On/Off
Switches the WAH on and off.
Loop On/Off
Switches the LOOP on and off.
OD/DS On/Off
Switches the OVERDRIVE/DISTORTION
on and off.
Preamp On/Off
Switches the PREAMP/SPEAKER on and
off.
EQ On/Off
Switches the EQ on and off.
FX-2 On/Off
Switches the FX-2 on and off.
Delay On/Off
Switches the DELAY on and off.
Chorus On/Off
Switches the CHORUS on and off.
Reverb On/Off
Switches the REVERB on and off.
Amp Ctl On/Off
Switches the AMP CTL on and off.
MANUAL On/Off
Switches the MANUAL on and off.
TUNER On/Off
Switches the TUNER/BYPASS on and off.
Master BPM (TAP)
Used for tap input of the Master BPM.
Delay Time (TAP)
Used for tap input of the delay time.
MIDI Start/Stop
Controls the Start/Stop of external MIDI de-
vices (such as sequencers).
MMC Play/Stop
Controls the Play/Stop of external MIDI de-
vices (such as hard disk recorders).
Patch Level Inc1
Increases the patch volume level by 10 units.
Patch Level Inc2
Increases the patch volume level by 20 units.
Patch Level Dec1
Decreases the patch volume level by 10 units.
Patch Level Dec2
Decreases the patch volume level by 20 units.
Hold Delay Stop
When “Hold” (p. 30) is selected for the DELAY
type, the performance is instantly stopped.
Solo A&B On/Off
Switches the preamp SOLO, for both chan-
nel A and B, on and off.
* If one of the two channels is off, both will be
turned on.
Patch Num. Inc
Switches to the next higher patch number in
the same bank as the currently selected patch.
Patch Num. Dec
Switches to the next lower patch number in
the same bank as the currently selected patch.
Patch Bank Inc
Switches to the next higher bank number.
Patch Bank Dec
Switches to the next lower bank number.
GT-8_e.book 55 ページ ２００７年６月２９日 金曜日 午後３時５５分
