background image

60

4   User's Reference

Messages

Meaning

An operation command was given while the
cover  is open.

Test printing was attempted with no  material
loaded.

Ink has been used up.

An ink cartridge was removed.
A request to insert an ink cartridge was made
from the FJ-50/40.

A request to remove an ink cartridge was made
from the FJ-50/40.

A request to insert a cleaning cartridge was made
from the FJ-50/40.

A request to remove a cleaning cartridge was
made from the FJ-50/40.

Check that the drain bottle is set in position when
filling ink.
* This message appears before operations that

will discharge large amounts of ink.
There is a chance of discharged ink overflow-
ing if operations are carried out while the drain
bottle is full.
As a guide, you should discard discharged ink
when the bottle is about half-full.

Check that the drain bottle is set in position when
filling ink.

Operation was paused by pressing the [PAUSE]
key, but there is still some remaining data.

To continue, press the [ENTER] key.

Emergency stop was effected.
* "CLOSE THE COVER" is also displayed

repeatedly.

   Audible alert each 10 sec.
   After 1 min., audible alert goes continuously.

Action

Close the cover.

Load the material and try again.
Press the [ENTER] key to continue.

Replace the empty ink cartridge.

Insert the specified ink cartridge.

Take out the specified ink cartridge.

Insert the specified cleaning cartridge.

Take out the specified cleaning cartridge.

Remove the drain bottle from the FJ-50/40,
discard the collected ink, then reinstall the drain
bottle.  Press the [ENTER] key to continue.

Set the drain bottle in place.

Pressing the [PAUSE] key again to resume
operation.
Pressing the [SETUP] key while paused causes
remaining data to be cleared and returns to the
NOT READY mode.

Press the [ENTER] key.

Close the cover.
* When restarting print, such detect like raster

line or shift of band may happen.

Messages

CLOSE THE COVER

SHEET UNLOADED

INK EMPTY

        [KCMcmY] 

*

SET CARTRIDGE

        [KCMcmY] 

*

REMOVE CARTRIDGE

        [KCMcmY] 

*

SET CL-LIQUID

        [KCMcmY] 

*

REMOVE CL-LIQUID

        [KCMcmY] 

*

DISCARD

      DRAIN INK

INSTALL

      DRAIN TANK

TO CANCEL,

 PRESS SETUP KEY

TO CONTINUE,

 PRESS ENTER KEY

DRY-UP OF HEAD

 MAY GIVE DAMAGE

* [KCMcmY] : This indicates the ink color.  The character indicating the color of the ink cartridge port flashes when operation is necessary.

    K = Black     C = Cyan     M = Magenta     c = Light Cyan (O = Orange)     m = Light Magenta (G = Green)     Y = Yellow

[Example]

INK EMPTY
        [

K

CM

c

mY]

If "K" and "c" are flashing

Black and Light Cyan inks have run out.

Summary of Contents for FJ-40



































































Reviews: