185
Effects List
Over
view
Sound 1
Sound 2
Sound 3
Pad
Sampler
Menu/System
Appendix
Sequencer
These settings allow you to select the desired type of reverb, and its
characteristics.
Reverb Parameters
Parameter
Value
Description
Reverb
Type
00 (OFF),
01 (REVERB),
02 (SRV ROOM),
03 (SRV HALL),
04 (SRV PLATE),
05 (GM2 RE-
VERB),
06 (ROOM),
07 (HALL),
08 (PLATE),
09 (STUDIO),
10 (CHURCH)
Type of reverb
Type: 01 (REVERB)
Type
ROOM1,
ROOM2,
STAGE1,
STAGE2,
HALL1, HALL2,
DELAY,
PAN-DELAY
Type of reverb/delay
ROOM1: short reverb with high density
ROOM2: short reverb with low density
STAGE1: reverb with greater late rever-
beration
STAGE2: reverb with strong early reflections
HALL1: very clear-sounding reverb
HALL2: rich reverb
DELAY: conventional delay effect
PAN-DELAY: delay effect with echoes
that pan left and right
Time
0–127
Time length of reverberation
(Type: ROOM1–HALL2)
Delay time
(Type: DELAY, PAN-DELAY)
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
cut, or “damped.” If you do not want to cut the
high frequencies, set this parameter to BYPASS.
Delay
Feedback
0–127
Adjusts the amount of delay feedback when
the Type setting is DELAY or PAN-DELAY.
Type: 02 (SRV ROOM)/03 (SRV HALL)/04 (SRV PLATE)
Pre
Delay
0.0–100.0 ms
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time
0–127
Time length of reverberation
Size
1–8
Size of the simulated room or hall
High Cut
160 Hz–12.5 kHz,
BYPASS
Adjusts the frequency above which the high-
frequency content of the reverb will be re-
duced. If you do not want to reduce the high
frequencies, set this parameter to BYPASS.
Density
0–127
Density of reverb
Diffusion
0–127
Adjusts the change in the density of the reverb
over time. The higher the value, the more the den-
sity increases with time. (The effect of this setting
is most pronounced with long reverb times.)
LF Damp
Freq
50–4000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
LF Damp
Gain
-36–0 dB
Adjusts the amount of damping applied to
the frequency range selected with LF Damp.
With a setting of “0,” there will be no reduc-
tion of the reverb’s low-frequency content.
HF Damp
Freq
4000 Hz–12.5 kHz Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
HF Damp
Gain
-36–0 dB
Adjusts the amount of damping applied to
the frequency range selected with HF Damp.
With a setting of “0,” there will be no reduc-
tion of the reverb’s high-frequency content.
Type: 05 (GM2 REVERB)
Character
0–7
Type of reverb
0–5: reverb
6, 7: delay
Pre-LPF
0–7
Cuts the high frequency range of the sound
coming into the reverb.
Higher values will cut more of the high
frequencies.
Level
0–127
Output level of reverbration
Time
0–127
Time length of reverberation
Delay
Feedback
0–127
Adjusts the amount of the delay sound that is
fed back into the effect when the Reverb
Character setting is 6 or 7.
Type: 06 (ROOM)/09 (STUDIO)
Pre Delay
0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time
0.1–3.0 sec
Time length of reverberation
Low
Damp
Freq
20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low
Damp
1–100 %
Adjusts the amount of damping applied to
the frequency range selected with LF Damp.
With a setting of “100%,” there will be no re-
duction of the reverb’s low-frequency con-
tent.
Hi Damp
Freq
1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High
Damp
1–100 %
Adjusts the amount of damping applied to
the frequency range selected with HF Damp.
With a setting of “100%,” there will be no re-
duction of the reverb’s high-frequency con-
tent.
High Cut
1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be re-
duced.
Type: 07 (HALL)/08 (PLATE)/10 (CHURCH)
Pre Delay
0–127
Adjusts the delay time from the direct sound
until the reverb sound is heard.
Time
0.1–6.0 sec
Time length of reverberation
Low
Damp
Freq
20–1000 Hz
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or “damped.”
Low
Damp
1–100 %
Adjusts the amount of damping applied to
the frequency range selected with LF Damp.
With a setting of “100%,” there will be no re-
duction of the reverb’s low-frequency con-
tent.
Hi Damp
Freq
1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb sound will be
reduced, or “damped.”
High
Damp
1–100 %
Adjusts the amount of damping applied to
the frequency range selected with HF Damp.
With a setting of “100%,” there will be no re-
duction of the reverb’s high-frequency con-
tent.
High Cut
1000–10000 Hz
Adjusts the frequency above which the high-
frequency content of the reverb will be re-
duced.
Parameter
Value
Description
Fantom-G_r_e.book 185 ページ ２００９年７月２日 木曜日 午後２時５５分
