14
JULY.2004
CHECKING THE VERSION
NUMBER
1.
Set up the CUBE-60 as described below.
[Connections]
Connect an FS-5U foot switch to each of the three FOOT SW jacks (CH
SELECT, EFX, DELAY/REVERB).
Set the FS-5U polarity switches to the jack side. Do not connect anything to any
of the other jacks.
[Panel Settings]
• POWER SW: OFF
• BRIGHT SW: OFF
• SELECT SW: OFF
• LEAD AMP TYPE SW: ACOUSTIC
• All VRs: Minimum
The version number will not be displayed unless the connections and panel
settings are correct.
2.
Press down on the foot switch FS-5U connected to the DELAY/REVERB
jack while turning on the power.
3.
While continuing to press the FS-5U connected to the DELAY/REVERB
jack, press the FS-5U connected to the EFX jack and the FS-5U connected
to the CH SELECT jack, in that order, within four seconds. After all the
LEDs turn on, they begin to flash.
4.
Press the FS-5U connected to the DELAY/REVERB jack again.
This switches the CUBE-60 to version display status.
Check the version according to which of the POWER LED, the SELECT LED
(green), and the SELECT LED (red), are lit or off.
o: Lit
x: Off
If the EFX LED or DELAY/REVERB LED are lit at this time,the CPU or DSP
self-diagnosis is failure(NG).
The version is still indicated even when this occurs.
5.
Turn off the power.
TEST MODE
Required Equipment
• 1 pair of headphones
• 3 BOSS FS-5U foot switches (sold separately)
• 3 foot switch connector cables (phone-phone)
Entering Test Mode
1.
Set up the CUBE-60 as described below.
[Connections]
• Connect an FS-5U foot switch to each of the three FOOT SW jacks (CH
SELECT, EFX, DELAY/REVERB).
• Set the FS-5U polarity switches to the jack side.
• Do not connect anything to any of the other jacks.
[Panel Settings]
• POWER SW: OFF
• BRIGHT SW: OFF
• SELECT SW: OFF
• LEAD AMP TYPE SW: ACOUSTIC
• All VRs: Minimum
The CUBE-60 will not enter Test mode unless the connections and panel
settings are correct.
2.
Press down on the foot switch FS-5U connected to the DELAY/REVERB
jack while turning on the power.
3.
While continuing to press the FS-5U connected to the DELAY/REVERB
jack, press the FS-5U connected to the EFX jack and the FS-5U connected
to the CH SELECT jack, in that order, within four seconds. After all the
LEDs turn on, they begin to flash.
The LEDs are used in confirming whether tests have passed of failed, so
confirm here that all LEDs are capable of working properly.
Quitting Test Mode
Turn off the power to exit Test mode.
Skipping
Tests cannot be skipped in Test mode.
Test Items
1.
Version Display/CPU and DSP Test (determined automatically)
2.
Volume Test
3.
Switch Test
Test Details
1. Version Display/CPU and DSP Test
(determined automatically)
Press the FS-5U connected to the DELAY/REVERB jack.
The version is indicated by on/off status of the POWER LED, the SELECT LED
(green), and the SELECT LED (red).
LED
1.00
1.01
1.02
1.03
1.04
1.05
1.06
POWER
o
x
o
x
o
x
o
SELECT(Green)
x
o
o
x
x
o
o
SELECT(Red)
x
x
x
o
o
o
o
SELECT LED
GREEN
SELECT LED
RED
POWER LED
Summary of Contents for CUBE-60D
