background image

 

Model

 

8

 

Inserting the Batteries

 

1.

 

Slide the battery cover towards OPEN, then open 

the compartment.

 

fig.battery1.eps

 

2.

 

Place the batteries in the compartment.

 

Insert two AA dry cell batteries, checking the polarity to make 
sure that the positive and negative ends are oriented correctly.

 

fig.battery2.eps

 

3.

 

Close the battery cover.

 

Making the Connections

 

Connect the guitar’s endpin jack to your amp, mixer, or other device.

 

fig.connect-e.eps

 

* The PREAMP has no power switch. The power is turned on when the connection plug is plugged into a guitar’s endpin jack.
* Whenever connecting or disconnecting cords, be sure to have the volume for all connected equipment turned down first.
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power 

on all devices before making any connections.

* Be sure to turn down the volume completely before turning off the power. Even with the volume turned completely down, 

some sound may be audible as the unit is turned on; however, this does not indicate a malfunction.

* Once the connections have been completed, turn on power to your various devices in the order specified. By turning on 

devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.

 

When powering up:

 

Turn on the power to your guitar amp last.

 

When powering down:

 

Turn off the power to your guitar amp first.

 

* This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit 

will operate normally.

* The backlight may light up or flash at power-up, but this does not indicate a malfunction.

Mixer

Amplifier

Acoustic Guitar

Endpin jack

or

 

PREAMP

 

• Remove the batteries whenever 

the unit is to remain unused for 
an extended period of time.
This may cause battery fluid 
leakage.

 

If a battery has leaked, use a soft 
piece of cloth or paper towel to wipe 
all remnants of the discharge from 
the battery compartment. Then 
install new batteries. To avoid 
inflammation of the skin, make sure 
that none of the battery discharge 
gets onto your hands or skin. 
Exercise the utmost caution so that 
none of the discharge gets near your 
eyes. Immediately rinse the affected 
area with running water if any of the 
discharge has entered the eyes.

Summary of Contents for COSM

















Reviews: