Roland Cakewalk A-500S Owner'S Manual Download

Page: 62 / 80

Troubleshooting

If you experience problems, read this chapter first. It contains information that will help you solve the problem.

* For help with Windows or Macintosh operation, refer to the documentation for your computer or operating system.

Is the CD-ROM inserted correctly in your CD-ROM drive?

Make sure that the CD-ROM is correctly inserted in the CD-ROM drive.

Could the CD-ROM itself or the lens of your CD-ROM drive be dirty?

The installer may not operate correctly if the CD-ROM or the lens of your CD-ROM drive is dirty. Use a commercially
available CD cleaner or lens cleaner to clean the disc or lens.

Are you attempting to install from a networked CD-ROM drive?

The driver cannot be installed from a CD-ROM drive on the network.

Could you have connected the A-500S to your computer before installing the driver?

If you connect the A-500S to your computer before installing the driver, an error message may appear when you
begin the installation.

Uninstall the A-500S driver as described in

“Removing the driver”

(p. 55), and then install the A-500S driver once

again as described in

“Driver Installation and Settings”

(p. 13).

Are there any devices labeled “Other,” “Unknown,” or “?/!/X” in the Device Manager?

If driver installation was not completed successfully, the partially installed driver may remain in an incomplete state.

Uninstall the A-500S driver as described in

“Removing the driver”

(p. 55), and then install the

A-500S once again as described in

“Driver Installation and Settings”

(p. 13).

Problems when installing the driver

Can’t start up the installer

A warning or error appears during the installation (Windows)

A-500S_e.book 62 ページ２０１０年２月１９日　金曜日　午後８時３分

Summary of Contents for Cakewalk A-500S

















































































Search results

Summary of Contents for Cakewalk A-500S

Reviews:

Related manuals for Cakewalk A-500S

Brands by name

Popular brands

Roland Cakewalk A-500S, Owner'S Manual

Search results

Summary of Contents for Cakewalk A-500S

Reviews:

Related manuals for Cakewalk A-500S

Brands by name

Popular brands