Raise and lower the six sliders TOTAL through DATAENTRY, and check that the value changes from
0—10 in correspondence to the slider movements.
(If there is a problem, refer to check 1.)
ê
This completes the slider VR test.
Action :
check 1 :
L BOARD BR702...706, IC707, 708
R BOARD VR201
PANEL L BOARD CN705 <=> MAIN BOARD CN11
PANEL R BOARD CN201 <=> MAIN BOARD CN5
MAIN BOARD IC7
4 : Pedal controller test
Summary : Check the operation of the pedal controller.
Procedure : Press numeric key 4 to enter the pedal controller test.
ê
Connect the EV-5 to FC, and TOTAL VOL and move the pedal,checking that the displayed “FC”, and
“Vo” values change from 0—10.
(If there is a problem, refer to check 1.)
ê
Connect the DP-6 to FS, and HOLD and move the pedal, checking that the displayed “FS” and “Hold”
values change from “O” to “-”.
(If there is a problem, refer to check 2.)
ê
This ends the pedal/breath controller test.
Action :
check 1 :
JACK B BOARD JK 117, 118
JACK B BOARD CN101<=> PANEL L BOARD CN706
PANEL L BOARD IC708
PANEL L BOARD CN705 <=> MAIN BOARD CN11
MAIN BOARD IC7
check2 :
JACK BOARD JK 115, 116
JACK BOARD CN102 <=> MAIN BOARD CN4
MAIN BOARD IC7
5 : Bender value setting
Summary : Specify the dead region at the center of the bender
Procedure : Press numeric key 5 to enter the bender setting item.
ê
The MIN and MAX values of the current dead area will be displayed.
Lower the bender all the way to the left, gradually return it to the center and press TRANSPOSE to set
the MIN value.
ê
Raise the bender all the way to the right, gradually return it to the center and press PORTAMENTO to
set the MAX value.
16
A-70
Sept, 1997
ê
This completes the bender settings.
TRANSPOSE
MONO
PORTAMENTO
NOTE: After setting the bender values, be sure to perform
the bender/wheel test to check operation.
*
If after performing the bender/wheel test you were
unsuccessful in making the setting, use the following
procedure to manually set the dead region.
$
Manual adjustment of the dead region
1. Use the “<” cursor key to select MIN setting mode.
2. Use the “>” cursor key to select MAX setting mode.
3. Use the INC and DEC keys to increase/decrease the setting.
6 : Bender/wheel test
B-
I
B+
I
Bm
I
W+
I
W-
I
Wm
I
(1) (2) (3) (4) (5) (6)
Summary : Check the operation of the bender and wheels.
Procedure : Press numeric key 6 to enter bender/wheel test mode.
ê
Move the bender toward the left and check that (1) in the diagram changes from 0 to over 6(See
NOTE1).
When the bender is released, the value should be 0.
(If there is a problem, check the bender value setting, and the items of check 1.)
ê
Move the bender toward the right and check that (2) in the diagram changes from 0 to over 6(See
NOTE1).
When the bender is released, the value should be 0.
(If there is a problem, check the bender value setting,and the items of check 1.)
ê
Move the bender toward the rear and check that (3) in the diagram changes from 0 to over 6(See
NOTE1).
(If there is a problem, check the items of check 1.)
ê
Move wheel 1 toward the rear and check that (4) in the diagram changes from 0 to over 6(See NOTE1).
(If there is a problem, check the items of check 2.)
ê
Move wheel 1 toward yourself and check that (5) in the diagram changes from 0 to over 6(See NOTE1).
(If there is a problem, check the items of check 1.)
ê
Move wheel 2 toward yourself and check that (6) in the diagram changes from 0 to over 6(See NOTE1).
Summary of Contents for A-70
