background image

4

2. COMPONENTS

This product is manufactured with CFC-free polyurethane insulation foam, a vitrified steel 
tank and copper heating elements. It also comes with a magnesium anode and a basic 
control panel made of PP.

The product comes with the following components:

• 

Product with sheathed heating elements

• 

Basic control panel with external thermal regulator

• 

T/P valve 0.7 MPa 90ºC and electrolytic fittings

• 

Installation and user manual

3. INSTALLATION - GENERAL

3.1.  Suitability

The product is suitable for domestic hot water systems where the cold mains water supply 
has a maximum supply pressure of 0.9 MPa. Reduced performance is available at lower 
pressures, but the product is not suitable for pressures lower than 0.15 MPa and a flow rate
of 20 litres per minute. The neccessary safety equipment to comply with all national 
legislation is available for purchase from Rointe. 

3.2. Water supply

The water supply to the cylinder should be potable water direct from a public mains water 
supply with any water treatment equipment functioning correctly. For optimum performance 
the unit should be fed via a 15 mm or 22 mm diameter supply pipe direct from the mains 
water entry point to the property and supplies a maximum pressure of 0.9 MPa. The unit 
can operate with a minimum supply pressure of 0.15 MPa and a flow rate of at least 20 litres 
per minute, but flow from the outlets will be low if several outlets are used simultaneously. 
The cylinder control equipment is factory set to limit the system operating pressure to 0.3 
MPa. The maximum supply pressure into the pressure-reducing valve is 0.9 MPa. 

3.3. Taps and fittings

All taps and fittings incorporated in the unvented system should have a rated operating 
pressure of 0.7 MPa or above.

We recommend using a Rointe Trusted Supplier. Find your nearest one by calling us on 

0203 321 5928

 or using the locator at 

www.rointe.co.uk

.

IMPORTANT:

  Before installation, please locate the metal tag and note the product 

reference and serial number. You will need this information to register your guarantee.

Summary of Contents for Geneva 050DHW4





















Reviews: