ROHS ITX-i9453 User Manual Download Page 33 | Manualshive

Page: 33 / 68

background image

ITX-i9453 User’s Manual

BIOS

32

Halt On

This ﬁeld determines whether or not the system will halt if an error is

detected during power up.

All errors (default)

Whenever the BIOS detects a non-fatal error, the

system will stop and you will be prompted.

No errors

The system boot will not be halted for any error that

may be detected.

All, But Keyboard

The system boot will not be halted for a keyboard

error; it will stop for all other errors.

All, But Diskette

The system boot will not be halted for a disk error; it

will stop for all other errors.

All, But Disk/Key

The system boot will not be halted for a keyboard

or disk error; it will stop for all others.

«
...
31
32
33
34
35
...
»

Summary of Contents for ITX-i9453





































































Reviews:

No comments

Related manuals for ITX-i9453

Brand: Datavan Pages: 15

Brand: Intel Pages: 97

Brand: JETWAY Pages: 48

Brand: ECS Pages: 70

Freescale MC9S08MM128

Brand: NXP Semiconductors Pages: 12

Brand: NXP Semiconductors Pages: 40

Brand: Socket Pages: 37

SUPER i2DMR-8G2

Brand: Supero Pages: 78

Brand: Maxim Pages: 33

Brand: Laird Pages: 17

S5U12517P00C100

Brand: Epson Pages: 24

Brand: Epson Pages: 33

Brand: Epson Pages: 23

Brand: Epson Pages: 31

Brand: Epson Pages: 28

Brand: Epson Pages: 27

S1V30080F00A300

Brand: Epson Pages: 39

S5U13506P00C100

Brand: Epson Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands