Rohde & Schwarz CMW-B400B User Manual Download

Page: 59 / 97

Command Reference

R&S

CMW-B400B/-B405A

User Manual 1176.8116.02 ─ 04

ABORt:AUDio:MEAS:ANALog
INITiate:AUDio:MEAS:DIGital
STOP:AUDio:MEAS:DIGital
ABORt:AUDio:MEAS:DIGital

Starts, stops, or aborts an analog or digital audio measurement:

●

INITiate...

starts or restarts the measurement; the R&S

CMW enters the

"RUN" state.

●

STOP...

causes a running measurement to stop after the current evaluation

period is terminated and valid results are available; the R&S

CMW enters the

"RDY" state.

●

ABORt...

causes a running measurement to stop immediately; the R&S

CMW

enters the "OFF" state.

Use

FETCh...STATe?

to query the current measurement state.

See also: "Measurement Control" in the R&S

CMW user manual, chapter "Remote

Control"

Example:

See

Single Tone Measurement

Usage:

Event

Firmware/Software:

V3.2.10

Manual operation:

See

"Digital Meas (Softkey)"

on page 29

FETCh:AUDio:MEAS:ANALog:STATe?
FETCh:AUDio:MEAS:DIGital:STATe?

Queries the main measurement state. Use

FETCh:...:STATe:ALL?

to query the

measurement state including the substates. Use

INITiate..., STOP...,

ABORt...

to change the measurement state.

See also: "Measurement Control" in the R&S

CMW user manual, chapter "Remote

Control"

Return values:

OFF | RUN | RDY

OFF:

measurement switched off, no resources allocated, no

results available (when entered after

ABORt...

)

RUN:

measurement running (after

INITiate..., READ...

synchronization pending or adjusted, resources active or queued

RDY:

measurement has been terminated, valid results may be

available
*RST:

OFF

Example:

See

Single Tone Measurement

Usage:

Query only

Firmware/Software:

V3.2.10

Manual operation:

See

"Digital Meas (Softkey)"

on page 29

Audio Measurements

深圳德标仪器

135-1095-0799

Summary of Contents for CMW-B400B


































































































Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands

Rohde & Schwarz CMW-B400B, User Manual

Search results

Summary of Contents for CMW-B400B

Reviews:

Related manuals for CMW-B400B

Brands by name

Popular brands