manualshive.com logo in svg

Rohde & Schwarz CMW-B400B, User Manual

Share
Download
Rohde & Schwarz CMW-B400B User Manual Download Page 40

GUI Reference

R&S

®

CMW-B400B/-B405A

40

User Manual 1176.8116.02 ─ 04

4.4 Audio Generator Settings

To access the analog and digital generator settings, select the "Analog Meas" tab or
the "Digital Meas" tab and press the "Config" hotkey. The tabs are only displayed if the
currently active scenario involves internal audio measurements and generators.

The following sections describe the "Analog Gen" and "Digital Gen" tabs of the configu-
ration dialog box.

Fig. 4-10: Configuration dialog box for measurements and generators

The screenhots in the following sections show the settings of the analog generator.
The settings of the digital generator are similar. Settings that are configured for analog
signals as voltages, are configured for digital signals as full-scale values.

●

General Settings

..................................................................................................... 40

●

Single Tone Settings

...............................................................................................41

●

Multitone Settings

....................................................................................................41

●

FFT Noise Settings

................................................................................................. 44

4.4.1 General Settings

The settings at the top of each generator tab select the type of the generated signal
and couple the generator to a measurement.

Fig. 4-11: General generator settings

Routing

..........................................................................................................................40

Signal Type

................................................................................................................... 41

Analyzer Coupling

......................................................................................................... 41

Routing

Displays the output connector at which the generated audio signal is available.

 

 

Audio Generator Settings

深圳德标仪器 

135-1095-0799

Summary of Contents for CMW-B400B


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands