manualshive.com logo in svg

Rohde & Schwarz 4091.7009.02, Getting Started

Share
Download
Rohde & Schwarz 4091.7009.02 Getting Started Download Page 54

Software and Firmware Update

R&S

®

 EB510

54

Getting Started 4091.7338.02 ─ 01

If the R&S

 

EB510 cannot reboot

Because the Update32 Tool performs its firmware updates over the LAN,
there could be a conflict if another user is running the tool in the same network.
The R&S

 

EB510 might "hang" after a reboot because the bootloader gets

"trapped" by this Update32 on the network. In such cases the best advise is:
unplug the network cable during boot-up and find out who else is running
Update32 on the corporate network.

4.4

GUI Installation for Remote Access

This section explains how to install the Remote GUI for use on a notebook or desk-
top PC.

Internal installation

If you want to install the GUI on the R&S

 

EB510, follow the procedure descri-

bed in 

​

chapter 4.2, "Receiver Firmware and GUI Update for EB510 with front

control panel"

, on page 40.

4.4.1

Preparations

Required files and accessories

The Remote Access GUI can be retrieved from either one of the locations mentioned
at 

​

"CD-ROM and Downloads"

 on page 40.

Retrieving the IP address of a R&S

 

EB510

It is more convenient to use DHCP with the serial number of the R&S

 

EB510.

For example, if the serial number is 100.001-002, the DHCP name will be "rs-
eb510-100001-002". If DHCP is unavailable, it is advisable to run the
"Update32" tool as explained in: 

​

chapter 4.5, "Changing the IP

Address"

, on page 59 and assign a static IP address.

 

 

GUI Installation for Remote Access

Summary of Contents for 4091.7009.02






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands