PRT12MF PRT62MF PRT64MF PRT66MF Installation Manual.doc
2019-07-02
2/2
F
IRMWARE UPDATE
The update requires connection of reader to computer with RUD-1 interface
(fig. 1) and starting RogerISP software. The latest firmware file is available at
Firmware update procedure:
1. Connect the reader to RUD-1 interface (fig. 1) and connect the RUD-1 to
computer’s USB port.
2. Place jumper on FDM contacts (fig. 2).
3. Restart the reader (switch power supply off and on or short RST contacts for
a moment).
4. Start RogerISP program.
5. Select serial port with RUD-1 interface and
Device Programmer
option.
6. Specify path to firmware file (*.hex).
7. Click
Update
to start firmware upload with progress bar in the bottom.
8. When the update is finished, remove jumper from FDM contacts and restart
the reader.
Note: After firmware update it may be necessary to start Memory reset
procedure.
A
PPENDIX
Fig. 2 Service contacts
Table 1. Terminals and wires
Screw
terminal
Wire colour
Description
12V
Red
Supply plus
GND
Black
Ground
IN1
Yellow
IN1 input line
IN2
Blue
IN2 input line
RTS
Violet
RS232 interface RTS line
CLK
Green
CLK line
DTA
Brown
DTA line
TMP
White
Tamper switch
TMP
Grey
Tamper switch
NC
Grey-pink
REL1 relay output (NC)
COM
Red-blue
REL1 relay common terminal
NO
Pink
REL1 relay output (NO)
Table 2. Specification
Supply voltage
Nominal 12VDC, min./max. range 10-15VDC
Current
consumption
(average)
PRT12MF/PRT64MF:
~85 mA
PRT12MF-BK/PRT62MF/PRT66MF: ~65 mA
Inputs
Two (IN1..IN2) NO inputs, approx. 3.5 triggering
level
Relay output
Relay output (REL1) with single NO/NC contact,
30V/1.5A DC/AC max. load, available only in
PRT64MF and PRT66MF
Tamper protection
Isolated 50mA/24V contacts, shorted when
enclosure is closed
Proximity cards
13.56MHz according to ISO14443A and MIFARE
Reading range
Up to 6 cm.
Note: Reading distance is defined for good quality
proximity cards placed in optimal position against the
reader. For all readers the optimal position for card reading
is in the front of the device (card surface parallel to the
front).
Distances
150m maximal cable length for RACS CLK/DTA
bus between controller and reader
IP Code
IP65
Environmental class
(according to EN 50133-1)
Class IV, outdoor general conditions, temperature:
-
25°C to +60°C, relative humidity: 10 to 95% (no
condensation)
Dimensions H x W x D and
weight
PRT12MF: 152,5 x 46 x 23(35) mm; 150g
PRT62MF: 100 x 45 x 25 mm; 100g
PRT64MF: 115 x 80 x 35 mm; 120g
PRT66MF: 85 x 85 x 27 mm; 120g
Certificates
CE
Fig. 3 Connection of door lock and exit button to PRT64MF or PRT66MF reader
– Simple standalone mode
Note: PRT12MF and PRT62MF readers are not equipped with relay. In their
case a door lock can be controlled by external relay connected to configured
CLK or DTA transistor output.
Fig. 4 Connection of PRT readers in RACS 4 system
– terminal (online) mode
Fig. 5 Connection of reader to controller via Wiegand interface
This symbol placed on a product or packaging indicates that the
product should not be disposed of with other wastes as this may
have a negative impact on the environment and health. The user is
obliged to deliver equipment to the designated collection points of
electric and electronic waste. For detailed information on recycling,
contact your local authorities, waste disposal company or point of
purchase. Separate collection and recycling of this type of waste
contributes to the protection of the natural resources and is safe to
health and the environment. Weight of the equipment is specified in
the document.
Contact:
Roger Sp. z o. o. sp. k.
82-400 Sztum
Gościszewo 59
Tel.: +48 55 272 0132
Fax: +48 55 272 0133
Tech. support: +48 55 267 0126
Web:
