MC16-RAW-KIT Installation Manual.doc
2019-05-13
1/2
Roger Access Control System
MC16-RAW-KIT Installation Manual
Firmware version: n/a
Document version: Rev. A
This document contains minimum information that is necessary for initial setup
and installation of the kit. The detailed description of configuration parameters
and functionalities of all components is specified in respective Operating
manuals available at
I
NTRODUCTION
MC16-RAW-KIT is designed to control from one to sixteen doors in RACS 5
system. Doors can be read-in or read-in/out type when equipped with MCT-IO
series readers (RS485). The kit includes MC16-RAW module and ME14-40VA
metal box with 18VAC/40VA transformer. The box is adapted to installation of
7Ah battery for emergency supply.
In case of MC16-RAW module it is required to order and upload license, which
specifies its functionalities including the number of controlled doors. Alternatively,
depending on the type of license the module can be operated not only as MC16-
PAC door access controller but as any MC16 type controller (e.g. MC16-HRC
hotel controller) and when uploaded with new firmware the module can also be
operated as expander (e.g. MCX16-AP).
L
ICENSE UPLOAD
The license for MC16-PAC type controller is uploaded to the memory card of
MC16-RAW module.
License upload procedure:
1. Disconnect power supply, press memory card at MC16-RAW module and
remove it from the socket.
2. Insert the card into standard reader for FLASH memory cards and connect
the reader to computer’s USB port.
3. Copy ordered license.cfg file into memory card.
4. Insert memory card into socket of MC16-RAW module.
5. After restoring power supply, the module will work as controller with
properties defined by its license.
Note: The MC16 without license or with invalid license is not operated in RACS 5
system.
C
ONFIGURATION WITH
R
OGER
VDM
PROGRAM
Low level configuration with RogerVDM software mainly concerns MC16
controller. Additionally it is necessary to define individual addresses for MCT
series readers according to their installation manuals.
MC16 programming procedure with RogerVDM software:
1. Connect the controller to Ethernet network and define the IP address of your
computer in the same subnetwork as the controller with 192.168.0.213
default IP address.
2. Start RogerVDM program, select
MC16 v1.x
device, the latest firmware
version and
Ethernet
communication channel.
3. Select from the list or enter manually the IP address of controller, enter 1234
communication key and start the connection with the controller.
4. In the top menu select
Tools
and then
Set communication key
to define your
own password for the controller.
5. In the main window specify your own IP address of the controller.
6. Optionally enter comments for controller and its object to facilitate their
identification during further configuration of the system.
7. Optionally backup settings clicking
Send to File…
8. Click
Send to Device
to update the configuration of controller and disconnect
by selection of
Device
in the top menu and then
Disconnect
.
M
EMORY RESET
Memory reset procedure resets all settings to default ones and results in
192.168.0.213 IP address and empty communication key.
MC16 memory reset procedure:
1. Disconnect power supply
2. Short CLK and IN4 lines.
3. Restore power supply, all LEDs will flash and wait min. 6s.
4. Remove connection between CLK and IN4 lines, LEDs will stop pulsating and
LED2 will be on.
5. Wait approx. 1.5 min till LED5+LED6+LED7+LED8 are pulsating.
6. Restart the controller (switch power supply off and on)
7. Start RogerVDM and make low level configuration.
F
IRMWARE UPDATE
New firmware can be uploaded to the controller with RogerVDM software. The
latest firmware file is available at
MC16 firmware update procedure:
1. Connect with the controller using RogerVDM software.
2. Backup settings by clicking
Send to
File…
3. In the top menu select
Tools
and then
Update firmware
.
4. Select firmware file and then click
Update
.
5. After firmware update wait till LED8 is pulsating.
6. Make or restore low level configuration in RogerVDM software.
Note: During the firmware update process, it is necessary to ensure continuous
and stable power supply for the device. If interrupted, the device may require
repair by Roger.
P
OWER SUPPLY
The kit is supplied from 18VAC/40VA transformer. The metal box offers space for
installation of typical 7Ah backup battery which is connected to BAT+ and BAT-
terminals of MC16 module.
Fig. 1 MC16-RAW-KIT
The installation can be done only by qualified person with all
necessary certificates concerning connection and maintenance
of 230VAC and low voltage networks.
Prior to starting the installation it is necessary to ensure that
230 VAC circuit is disconnected. All works inside the box must
be carried out with 230VAC supply voltage disconnected.
It is forbidden to use the kit without properly executed and
operational earthing system.
T
AMPER DETECTOR
The metal box is equipped with door contact which can be connected to one of
the inputs (e.g. IN8) and GND terminal of the controller. The anti-sabotage
function can be assigned to the input within high level configuration of the
system.
A
PPENDIX
Table 1. MC16 screw terminals
Name
Description
BAT+, BAT-
Backup battery
AC, AC
18VAC input power supply
AUX-, AUX+
12VDC/1.0 output power supply (for door lock)
TML-, TML+
12VDC/0.2A output power supply (for readers)
IN1-IN8
Input lines
GND
Ground
OUT1-OUT6
15VDC/150mA transistor output lines
A1,B1
RS485 bus
CLK, DTA
RACS CLK/DTA bus
A2,B2
Not used
