EN
25
1
General safety precautions
Warning
: incorrect installation may cause
severe damage or injury.
Read the instructions carefully before
installing the product.
This installation manual is intended for qualified personnel only.
ROGER TECHNOLOGY cannot be held responsible for any damage or
injury due to improper use or any use other than the intended usage
indicated in this manual.
Installation, electrical connections and adjustments must be
performed by qualified personnel, in accordance with best practices
and in compliance with applicable regulations.
Before installing the product, make sure it is in perfect condition
Disconnect the mains electrical power before performing any work.
Also disconnect any buffer batteries used.
Only use original spare parts when repairing or replacing products.
The packaging materials (plastic, polystyrene, etc.) should not be
discarded in the environment or left within reach of children, as they
are a potential source of danger.
WARNING! Handle electronic parts and terminals with
extreme care, as these parts are highly sensitive to static
electricity.
Handle the LED light strip with extreme care. Do not twist,
pull, tread on, bend or drill the strip casing.
2
Product description
The lights for the arm of the ROGER AGILIK, KB and BIONIK barrier
make the arm more visible in all conditions.
They are composed of a LED strip that is inserted inside the boom.
By configuring the command unit they are connected to, it is possible
to configure the start-up procedure (parameter
79
).
They are supplied in 4 sizes:
• ALED/4C:
Strip LED 4 metres with connections cable.
• ALED/6C:
Strip LED 6 metres with connections cable.
•
ALED/8C:
Strip LED 8 metres with connections cable.
•
ALED/12C:
Strip LED 12 metres with connections cable.
3
Technical specifications
MAINS POWER VOLTAGE
24 Vdc ±10%
MAXIMUM MAINS POWER
ABSORPTION
4W
ALED/4C
5W
ALED/6C
7W
ALED/8C
10W
ALED/12C
OPERATING TEMPERATURE
-20°C
+55°C
DEGREE OF PROTECTION
IP54
PRODUCT DIMENSIONS
ALED/4C
ALED/6C
ALED/8C
ALED/12C
15x6x4500 mm
15x6x7500 mm
15x6x9500 mm
15x6x13500 mm
WEIGHT
ALED/4C
ALED/6C
ALED/8C
ALED/12C
0,22 kg
0,29 kg
0,37 kg
0,52 kg
4
Installation
4.1
Adjusting length
If necessary, the LED light strip must be shortened.
1. Detach and remove the terminal black cap (
A
fig. 1).
2. Cut at the co 24V - + 24V / GND-GND (detail
B
).
ATTENTION: DO NOT CUT at the co 24V - + 24V /
A - B / GND - GND.
NB:
It is possible to cut the LED light strip every 1000 mm.
3. Fix the terminal black cap (
C
) onto the strip with silicone sealant.
Proceed with the installation as indicated in the following chapters,
based on the installed barrier model.
Whenever corrective actions are carried out,
pay the utmost attention when releasing,
locking or moving the internal mechanical
parts. These operations could be hazardous for the
user.
WARNING: only perform the installation procedures
with the unit disconnected from mains and with the
motor at a standstill.
4.2
Installation procedure AGILIK
If the arm is mounted on the barrier’s body, remove it.
Place the arm on a stable surface, making sure it is not scratched.
To insert the LEDs, proceed as follows (
Fig. 2
):
• Remove the cap from the end of the arm (detail
D
) loosen the
screw.
• Remove the two transparent side profiles.
• Making sure that the LEDs are facing outward (
detail E
), insert
the LED strip,the LED strip into the two transparent strips
pushing the rear part of the LED strip
gently.
• Secure the rubber adhesive under the LED strip in line with the
bend to protect it from the sharp aluminium edge (
detail F
).
• Insert the two transparent side profiles.
• Close the cap of the boom with the supplied screws.
• Feed the cable from the other side of the flange through the
dedicated hole indicated in
detail G
.
ATTENTION
The path of the pipe that guides the cable varies according
to the mounting direction of the rod. Check figure 3 to see
whether the rod is in RH or LH position.
To install the rod, follow the steps below:
• Pass the cable through the pipe and leave out about 20 cm. In
this way, the cable moves forward enough to leave the rod on the
ground during assembly.
• Secure the pipe with the cable clamp provided
(figure 4, detail
H)
• Pass the pipe through the hole provided on barrier’s structure
(figure 4, detail I)
.
• Secure the flange to barrier’s structure carefully observing pipe’s
path
(figure 4)
• Fix the rod to the flange
• Pull the free section of the cable while conveying it to the
opposite side
(figure 5)
• The free part of the cable is now found inside the body of
the barrier, behind the reduction gear. Take the cable to the
command unit passing to the right of the reduction gear and
rising towards the casing, as shown in
figure 5
.
Carry out the connections to the command unit as shown in
Fig. 6.
Connect the brown (or red) wire to the
+LUCI
terminal and connect
the blue (or black) wire to the
COM
terminal.
To see how to configure the lights, please refer to the manual of the
command unit (setting of parameter
79
).
Summary of Contents for AG/ALED12C
