background image

- 12 -

Warranty

All 

 microphones are warranted for one year 

from date of purchase. You can extend that to a full 

ten years if you register the microphone online at 

www.rodemic.com

.

The warranty covers parts and labour that may be 

required to repair the microphone during the warranty 

period. The warranty excludes defects caused by 

normal wear and tear, modifi cation, shipping damage, 

or failure to use the microphone as per the instruction 

guide.

If you experience any problem, or have any questions 

regarding your 

 microphone, fi rst contact the 

dealer who sold it to you. If the microphone requires a 

factory authorised service, return will be organised by 

that dealer. 

We have an extensive distributor/dealer network, but 

if you have diffi culty getting the advice or assistance 

you require, do not hesitate to contact us directly.

 Microphones

International

107 Carnarvon Street
Silverwater NSW 2128 Australia
Ph: 

+61 2 9648 5855

Fax: 

+61 2 9648 2455

USA

P.O. Box 4189
Santa Barbara, CA 93140-4189
Ph: 805 566 7777
Fax: 805 566 0071

Technical Support

For information and technical support questions contact:
[email protected]

In the Unites States and Puerto Rico, contact 
[email protected] or call 805 566 7777

In Australia, contact [email protected] or call (02) 9648 5855

Anywhere except Australia, the United States and Puerto Rico, 
contact [email protected] or call +61 2 9648 5855

Summary of Contents for NT 3













Reviews: