manualshive.com logo in svg

Rockwood 32082, Instructions Manual, Page: 8 / 8

Share
Download
Rockwood 32082 Instructions Manual Download Page 8

ADDITIONAL ITEMS

#32083 

Replacement Outer Lens Shield

#32084 

Replacement Inner Lens Shield

#21520 

Replacement Head Gear

© Copyright 2019 Easthill Group, Inc.     4/19     Instruction item #32082Q     Rev 1

If you have any questions about the use of this product, please contact 

The Eastwood Technical Assistance Service Department: 800.343.9353  >>  email: [email protected]

PDF version of this manual is available at eastwood.com

The Eastwood Company     263 Shoemaker Road, Pottstown, PA 19464, USA 

800.343.9353     eastwood.com

PROBLEM

CAUSE

CORRECTION

Auto-Dimming 

Does Not  

Function 

(will not 

darken)

Dirt may be blocking 

sensors located at 

upper area of the lens 

assembly

Clean lens assembly.

Batteries  

may be low

Expose the solar cells to bright light source  

to recharge.

Dirt may be blocking  

solar cells at upper  

portion of viewer area

Clean lens assembly.

Slow Response 

for Darkening

Operating temperature 

too low

Do not use below 23°F (-5°C).

Sensitivity setting may 

need adjustment

Follow “Sensitivity” section in instructions  

for adjustment procedure.

Poor Vision 

Through Lens

Dirt or excessive pitting 

may be blocking view

Clean lens assembly.

Helmet Slips 

During Use

Helmet fit not adjusted 

properly

Follow fit adjustment steps in instructions.

TROUBLESHOOTING

Summary of Contents for 32082









Reviews:

No comments