Rockwell ShopSeries RS2212, Manual, Page: 10 / 12

CoRdleSS dRill eN
10
Make the setting as follows:
1 - 4 for driving small screws
5 - 9 for driving screws into soft material
10 - 14 for driving screws into soft and hard
material
15 - 19 for driving screws into hard wood
20 for driving larger screws
for heavy drilling
6. dRilliNg
When drilling hard smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off center as the hole
is started. Hold the tool firmly and place the tip of the
bit at the point to be drilled. Depress the switch trigger
to start the tool. Move the drill bit into the work-piece,
applying only enough pressure to keep the bit drilling.
Do not force or apply side pressure to elongate a hole.
waRNiNg: Tungsten carbide drill bits should
always be used for concrete and masonry.
when drilling in metal, only use hSS drill bits in
good condition. always use a magnetic bit holder
when using short screwdriver bits. when
screw-driving, apply a small quantity of liquid soap
or similar to the screw threads to ease insertion.
7. uSiNg The SighT lighT
The sight light allows you to keep a clear view under
less illuminated circumstances. To turn on the light
simply press the on/off switch. When you release the
on/off switch, the light will be off.
PRoBleM SoluTioN
1. why doeS The dRill NoT TuRN oN wheN you PReSS
The SwiTCh?
The forward/reverse rotation control, which is on
top of the trigger, is positioned in the lock function.
Unlock the forward/reverse rotation control by putting
it into the required rotation position. Push the trigger
and the drill will start to rotate.
2. The dRill SToPS BefoRe The SCRew iS CoMPleTely
TighTeNed. why?
Verify the torque position of the variable clutch, you
can find the variable clutch between the chuck and
the drill body. Position 1 is the lowest torque (screw
driving force) and position 20 is the highest torque
(screw driving force). Position is for drill operation.
Regulate the variable clutch to a higher position to
reach the best result.
3. i CaNNoT fiT The BaTTeRy iNTo The BaTTeRy
ChaRgeR. why?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot.
4. ReaSoNS foR diffeReNT BaTTeRy PaCK woRKiNg
TiMeS.
Charging time issues, as above, and having not used
a battery pack for a prolonged time will reduce the
working life of the battery pack. This can be corrected
after several charge and discharge operations by
charging & working with your drill. Heavy working
conditions such as large screws into hard wood will
use up the battery pack energy faster than lighter
working conditions. Do not re-charge your battery
pack below 0
o
C and above 30
o
C as this will affect
performance.
MaiNTeNaNCe
Remove the battery pack from the tool before
carrying out any adjustment, servicing or
maintenance.
Your tool requires no additional lubrication or main-
tenance.
There are no user serviceable parts in your tool,
battery pack or charger. Never use water or chemi-
cal cleaners to clean your tool. Wipe clean with a dry
cloth. Always store your tool in a dry place. Keep
the motor ventilation slots clean. Occasionally you
may see sparks through the ventilation slots. This is
normal and will not damage your power tool.
Staple your purchase receipt here
Before returning this product for
warranty or any other reason, please call.
PoSiTeC auSTRalia PTy liMiTed
aBN 14 101 682 357
unit 15, 23 Narabang way Belrose 2085 NSw
australia
fRee Call 1300 889 028
EMAIL:office.sales@positec.com.au