Rockwell Automation PowerFlex 700S, User Manual, Page: 157 / 318

Programming and Parameters 3-99
PowerFlex 700S Phase II AC Drive User Manual - Publication 20D-UM006G-EN-P – July 2008
832 Anlg Out1 DInt
Link this parameter to an integer source parameter that will control Analog Output 1.
Default:
Min/Max: 0
-/+2147483648
✓
RW 32-bit
Integer
833 Anlg Out1 Real
Link this parameter to a real (floating point) source parameter that will control Analog Output
1.
Default:
Min/Max: 0.0000
-/+2200000000.0000.0000
✓
RW Real
834 Anlg Out1 Offset
Provides an offset for Analog Output 1 before the scaling and limit blocks in the Analog Output
1 function. This parameter value is summed with either
Par 832 [Anlg Out1 DInt] or Par 833
[Anlg Out1 Real] at the beginning of the function.
Default:
Min/Max: 0.0000
-/+2200000000.0000
✓
RW Real
835 Anlg Out1 Scale
Scales the range of the source parameter to the range of Analog Output 1. For example: If Par
831 [Anlg Out1 Sel] is set to 1 “Output Freq”, the output frequency of the drive is 0 - 60Hz and
you enter “6” in this parameter, Par 837 [Anlg Out1 Value] = 6Hz per 1V, or 0 - 60Hz.
Par 832 [Anlg Out1 DInt] or Par 833 [Anlg Out1 Real] is multiplied by this number after the limit
function.
Note: The turn-off point for this parameter has been changed from ±0.001 to ±0.0001 for
firmware version 4.002.
Units:
Default:
Min/Max: /V
0.0000
-/+2200000000.0000
✓
RW Real
836 Anlg Out1 Zero
Applies an offset to the scaled value of Analog Output 1. This parameter is summed with the
output of the scaling block. This sum produces
Par 837 [Anlg Out1 Value]. Typically this value
corresponds to 0V for Analog Output 1.
Units:
Default:
Min/Max: Volt
0.0000
-/+20.0000
✓
RW Real
837 Anlg Out1 Value
Displays the voltage reference for Analog Output 1 before the digital to analog conversion.
Units:
Default:
Min/Max: Volt
0.0000
-/+10.0000 RO Real
838 Anlg Out2 Sel
Identifies the signal used on Analog Output 2. If the desired signal is not available in the
selection list, choose option 0 - “User Select” and link with
Par 839 [Anlg Out2 DInt] or Par 840
[Anlg Out2 Real] to select the desired parameter for output. Refer to Par 831 for a list of
parameters that correspond to the option selected in this parameter.
Default:
Options: 3 =
0 =
1 =
2 =
3 =
4 =
5 =
6 =
7 =
8 =
9 =
10 =
11 =
12 =
13 = “Output Curr”
“User Select”
14 = “Reserved”
“Output Freq” 15 = “Motor TrqRef”
“Sel Spd Ref” 16 = “MtrTrqCurRef”
“Output Curr” 17 = “Speed Ref”
“Trq Cur (Iq)” 18 = “Speed Fdbk”
“% Motor Flux” 19 = “Torque Est”
“Output Power” 20 = “Scl Spd Fdbk”
“Output Volts” 21 = “RampedSpdRef”
“DC Bus Volts” 22 = “Spd Reg Out”
“PI Reference” 23 = “MOP Level”
“PI Feedback” 24 = “Trend 1 DInt”
“PI Error” 25 = “Trend 1 Real”
“PI Output” 26 = “Trend 2 DInt”
“Reserved” 27 = “Trend 2 Real”
839 Anlg Out2 DInt
Link this parameter to an integer source parameter that will control Analog Output 2.
Default:
Min/Max: 0
-/+2147483648
✓
RW 32-bit
Integer
840 Anlg Out2 Real
Link this parameter to a real (floating point) source parameter that will control Analog Output
2.
Default:
Min/Max: 0.0000
-/+2200000000.0000
✓
RW Real
841 Anlg Out2 Offset
Provides an offset for Analog Output 2 before the scaling and limit blocks in the Analog Output
2 function. This parameter value is summed with either
Par 839 [Anlg Out2 DInt] or Par 840
[Anlg Out2 Real] at the beginning of the function.
Default:
Min/Max: 0.0000
-/+2200000000.0000
✓
RW Real
842 Anlg Out2 Scale
Scales the range of the source parameter to the range of Analog Output 2. For example: If Par
838 [Anlg Out2 Sel] is set to 1 “Output Freq”, the output frequency of the drive is 0 - 60Hz and
you enter “6” in this parameter, Par 844 [Anlg Out2 Value] = 6Hz per 1V, or 0 - 60Hz.
Par 839 [Anlg Out2 DInt] or Par 840 [Anlg Out2 Real] is multiplied by this number after the limit
function.
Note: The turn-off point for this parameter has been changed from ±0.001 to ±0.0001 for
firmware version 4.002.
Units:
Default:
Min/Max: /V
0.0000
-/+2200000000.0000
✓
RW Real
843 Anlg Out2 Zero
Applies an offset to the scaled value of Analog Output 2. This parameter is summed with the
output of the scaling block. This sum produces
Par 844 [Anlg Out2 Value]. Typically this value
corresponds to 0V for Analog Output 2.
Units:
Default:
Min/Max: Volt
0.0000
-/+20.0000
✓
RW Real
844 Anlg Out2 Value
Displays the voltage reference for Analog Output 2 before the digital to analog conversion.
Units:
Default:
Min/Max: Volt
0.0000
-/+10.0000 RO Real
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype