Rockwell Automation PowerFlex 700S, User Manual, Page: 146 / 318

3-88 Programming and Parameters
PowerFlex 700S Phase II AC Drive User Manual - Publication 20D-UM006G-EN-P – July 2008
731 PLL Posit Out
Phased Locked Loop position output. This signal is precisely in phase with the input physical
device. A link should be made to it from the local drive auxiliary position input. (The local drive
is the one implementing PLL.)
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max: 0
-/+2147483648 RO 32-bit
Integer
732 PLL Posit OutAdv
Phased Locked Loop position advanced output. This signal is one position sample in advance
of
Par 731 [PLL Posit Out]. A link is normally made to this parameter from SynchLink.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max: 0
-/+2147483648 RO 32-bit
Integer
733 PLL FiltPositOut
Phased Locked Loop internal low pass filter output. This parameter is normally used to
properly scale an external velocity reference. See description of
Par 729 [PLL Ext SpdScale].
Note: This parameter was added for firmware version 3.01.
Units:
Default:
Min/Max: P.U.
0.0
-/+2200000000.0
✓
RW Real
734 PLL Speed Out
Phased Locked Loop velocity output. This signal is used as a velocity feed forward. It is
precisely in phase with the physical input device. A link should be made to it from one of the
inputs on the local drive. (The local drive is the one implementing PLL.) The 1 pu RPM of this
parameter is set by
Par 727 [PLL VirtEncdrRPM].
Note: This parameter was added for firmware version 3.01.
Units:
Default:
Min/Max: P.U.
0.0
-/+2200000000.0
✓
RW Real
735 PLL SpeedOut Adv
Phase Locked Loop velocity advanced output. This signal is one velocity reference sample in
advance of
Par 734 [PLL Speed Out]. A link is normally made to this parameter from
SynchLink. (Velocity reference is performed in the same task as the position regulator.)
Note: This parameter was added for firmware version 3.01.
Units:
Default:
Min/Max: P.U.
0.0
-/+2200000000.0
✓
RW Real
737 Posit TP Select
Enter or write a value to select position regulator data displayed in Par 738 [PositTP DataInt]
and Par 739 [PositTP DataReal].
Default:
Options: 0 =
0 =
1 =
2 =
3 =
4 =
5 =
6 =
7 =
8 = “Zero”
“Zero”
9 = “Limiter Out”
“del Xos Vout” 10 = “Ref EGR In”
“del Xcmd” 11 = “OffsetSpdLim”
“del Act Load” 12 = “Pt-Pt SpdLim”
“del Act Mtr” 13 = “Sec per Edge”
“Integ Error” 14 = “Edge per Sec”
“Xprop Out” 15 = “Ratio Guess”
“Fdbk Sel Alt” 16 = “Sync Count”
“PreLim Xvout”
738 PositTP DataDInt
Displays the integer data selected by Par 737 [Posit TP Select]. This display should only be
used if the selected value is Integer data.
Default:
Min/Max: 0
-/+2147483648 RO 32-bit
Integer
739 PositTP DataReal
Displays the real data selected by Par 737 [Posit TP Select]. This display should only be used
if the selected value is Real data.
Default:
Min/Max: 0.0
-/+8.0 pu RO Real
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype