Rockwell Automation PowerFlex 700S, User Manual, Page: 128 / 318

3-70 Programming and Parameters
PowerFlex 700S Phase II AC Drive User Manual - Publication 20D-UM006G-EN-P – July 2008
475 MC FaultTPSelect
Enter or write a value to select the Motor Control (MC) Fault Data displayed in Par 476 [MC FaultTP Value]. This parameter should not be changed by the user.
Notes: This parameter was added for firmware version 2.03. The value for option 67 was changed from “HH GateShort” to “MCStatus1” for firmware version 2.04.
Values 68 - 76 were added for firmware version 3.01.
476 MC FaultTP Value
Displays the data selected by Par 475 [MC FaultTPSelect]. This parameter should not be
changed by the user.
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: 0.0
+/- 2147483648 RO 32-bit
Integer
477 Est Theta Delay
Active only in Permanent Magnet motor mode (when Par 485 [Motor Ctrl Mode] equals 2
−
“PMag Motor”). Provides a delay for the function that compares the estimated rotor
position and the data from the position sensor.
Units:
Default:
Min/Max: mSec
10
2/1024 RW 16-bit
Integer
478 VPL Mem Password
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: 0
+/-2147483648 RW 32-bit
Integer
479 VPL Mem Address
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: 0
0 - 4294967295 RW 32-bit
Integer
480 VPL Mem Data Int
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: 32
+/-2147483648 RW 32-bit
Integer
481 VPL Mem Data Flt
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: 1.25 RW Real
482 VPL Mem Data Bit
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: 1.25 RW 32-bit
Integer
483 VPL Mem Link Int
Note: This parameter was added for firmware version 2.03.
Default:
Min/Max: +/-2147483648 RO 32-bit
Integer
484 VPL Mem Link Flt
Note: This parameter was added for firmware version 2.03.
RO Real
485 Motor Ctrl Mode
Enter a value to select the operating mode for the Motor Control (MC).
•
Value 0 - Field Oriented Control (FOC) is induction motor control with voltage
adaptation.
•
Value 1 - Field Oriented Control 2 (FOC 2) is induction motor control with temperature
adaptation. (This option is used only for motors manufactured by Reliance Electric -
Japan.)
•
Value 2 - Permanent Magnet Motor Control (Pmag Motor) is permanent magnet motor
operation.
•
Value 3 - V/Hz is volts per hertz motor control.
•
Value 4 - Test is the test mode.
Default:
Options: 0 =
0 =
1 =
2 = “FOC”
“FOC”
3 = “V/Hz”
“FOC 2” 4 = “Test”
“PMag Motor”
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype
Options:
0 = IqsRef2 14 = DcBus 29 = DbDuty 43 = RotorFluxEst 57 = VbusDrop 71 = HH OverLoad
1 = Ws 15 = VbusFdbk 30 = VelFdbkEnc0 44 = Ws2 58 = VdsMax 72 = HH Precharge
2 = We 16 = VbusFdbkFltr 31 = VelFdbkEnc1 45 = BusDropVolts 59 = VbusLow 73 = HH Fan Alarm
3 = We2 17 = VbusMemory 32 = VdsCmd2 46 = RecoverVolts 60 = VbusRising 74 = HH BusComm
4 = VdsCmd 18 = Kpwm 33 = VelFdbkOpt1 47 = TestDtoA0 61 = PreChrgDone 75 = HH HW Incomp
5 = VqsCmd 19 = ThetaE 34 = Reserved 48 = TestDtoA1 62 = FieldWeak 76 = HH GateShort
6 = VdsFdbk 20 = FldWeakActiv 35 = Reserved 49 = TestDtoA2 63 = Reserved
7 = VqsFdbk 21 = MtrFlxPU 36 = Reserved 50 = TestDtoA3 64 = DynamBrakeOn
8 = luFdbk 23 = SlipGainFltr 37 = Reserved 51 = RideThruActv 65 = Reserved
9 = IwFdbk 24 = SlipVdsCmd 38 = TorqueEst 52 = PreChrgReqVp 66 = MCStatusMon
10 = IdsFdbk 25 = MotorVolts 39 = TorqueEstFlt 53 = Reserved 67 = MCStatus1
11 = IqsFdbk 26 = BusUtil 40 = Reserved 54 = Reserved 68 = HH OverCurr
12 = IdsCmd 27 = IqsLimit 41 = PowerCalc 55 = Reserved 69 = HH BusOvrVlt
13 = IqsCmd 28 = VqsIdsCmd 42 = TorqueCmd 56 = TorqTrimActv 70 = HH Tr Desat